Differences

This shows you the differences between two versions of the page.

--- public:rangex-pro-manual [2023/12/22 15:38] – laurin
+++ public:rangex-pro-manual [2024/12/09 18:01] (current) – ↷ Page moved from internal:public:rangex-pro-manual to public:rangex-pro-manual admin
@@ Line 1: / Line 1: @@
 ====== RangeX Pro Manual ======
+{{:public:rangex_pro_overview.jpg?600|}}
 ===== General Information =====
@@ Line 23: / Line 25: @@
   * Bluetooth BLE: No cables needed, great for compass calibration. Slow reading speed.
   * internal USB C on the FC: Fastest connection, only needed for downloading flight logs.
+==== Center of Gravity Information ====
+For optimal performance, aim to position the COG (Center of Gravity) of the RangeX Pro as close to the dotted line as you can. When using a 6s 4500 mAh, ensure it sits toward the rear for better balance. This balance is crucial to maintain smooth flight dynamics and prevent vibrations.
+{{:public:rangex_pro_manual_cog.jpg}}
 ===== Before the first flight =====
@@ Line 61: / Line 69: @@
 {{:public:inav_rx_mapping.png}}
+==== Change Flight Modes ====
+To reassign buttons on your remote controller, assign AUX channels to each flight mode using Inav configurator.
+  * Connect the drone via USB port of the flight controller to your computer
+  * launch INAV configurator
+  * Connect to the correspondent port
+  * Navigate to "Modes" tab
+  * Choose AUTO for the mode in question and press the corresponding button on your TX
+  * Don't forget to hit save!
+{{:public:inav_modes.png}}
+=== **IMPORTANT** ===
+For all models that support GPS rescue: The GPS rescue should not be activated if you are within 50m of the starting point. If the drone is within 50m radius of the starting point and GPS rescue is activated, the drone will drop form the sky. Only activate GPS Rescue manually if the drone is more than 50m away from its starting point.
 ==== Binding your DJI Goggle ====
@@ Line 72: / Line 97: @@
 {{:public:dji-goggles-2.jpg?400|}}
 {{:public:dji_o3_bind.button.jpeg?400|}}
+==== LED Setup ====
+The LEDs can be turned on and off with your remote controller. The LEDs are soldered to the Crossfire diversity RX on channel 5. You can change the channel on Output 5 to your preferred switch in the menu of the crossfire Diversity RX after it has been bound to your remote.
+{{:public:Rangexpro_LED_setup.jpg?500|}}
@@ Line 89: / Line 120: @@
 {{:public:rangex_pro_compass_compressed.jpg}}
-==== LED Setup ====
-The LEDs can be turned on and off with your remote controller. The LEDs are soldered to the Crossfire diversity RX on channel 5. You can change the channel on Output 5 to your preferred switch in the menu of the crossfire Diversity RX after it has been bound to your remote.
-{{:public:Rangexpro_LED_setup.jpg?500|}}
-==== Change Flight Modes ====
-To reassign buttons on your remote controller, assign AUX channels to each flight mode using Inav configurator.
-  * Connect the drone via USB port of the flight controller to your computer
-  * launch INAV configurator
-  * Connect to the correspondent port
-  * Navigate to "Modes" tab
-  * Choose AUTO for the mode in question and press the corresponding button on your TX
-  * Don't forget to hit save!
-{{:public:inav_modes.png}}
-=== **IMPORTANT** ===
-For all models that support GPS rescue: The GPS rescue should not be activated if you are within 50m of the starting point. If the drone is within 50m radius of the starting point and GPS rescue is activated, the drone will drop form the sky. Only activate GPS Rescue manually if the drone is more than 50m away from its starting point.
 ===== Change Rates =====