Differences

This shows you the differences between two versions of the page.

--- public:omnix [2026/11/05 09:33] – [11.4 Fit lens covers and battery mount] laurin
+++ public:omnix [2026/11/05 10:28] (current) – [13.3 Use Gopro Preset] laurin
@@ Line 1: / Line 1: @@
-====== OMNIX 360 - Build Guide v5 ======
+====== OMNIX 360 Build Guide  ======
-====== (In Progress) not finish ======
-**Step-by-step build guide: Naked GoPro MAX 2 + Naked DJI O4 Pro**
-This guide shows each assembly operation directly below one or two relevant photographs. Follow the sequence carefully. Keep the propellers removed until the electrical checks are completed.
-**CAUTION - FRAGILE GOPRO LENS RIBBON CABLES:** The two lens flex cables are extremely fragile. Never pull, fold, twist, crease or pinch them. Handle the lens modules by their housing only, keep the flex cables relaxed, and open each locking connector before inserting or removing a cable. A damaged cable may cause a missing lens image or camera failure.
-===== Parts needed =====
+{{:public:omnix_large.png?600|}}
-  * OMNIX 360 Frame Kit (includes carbon and printed parts)
+This guide covers the OMNIX 360 frame with a naked GoPro MAX 2 and a naked DJI O4 Pro. Keep the battery disconnected during assembly. Leave the propellers off until all bench tests are complete.
+**Handle each GoPro lens module by its housing.** Support both lens ribbon cables whenever you move the assembly. Pulling, creasing or pinching a ribbon can cause loss of the image from that lens. Release any connector latch before removing or inserting its ribbon.
+===== Parts and equipment =====
+* OMNIX 360 Frame Kit (includes carbon and printed parts)
   * Flywoo AIO (recommended: Flywoo AIO V3)
   * 4x motors (recommended: T-Motor 1404 3800KV)
@@ Line 13: / Line 18: @@
   * Naked DJI O4 Pro and camera
   * ELRS receiver and compatible antenna
-  * FPV antennas (recommended: Flywoo 5.8 GHz Light Brass 80mm)
+  * FPV antennas (recommended: Flywoo 5.8 GHz Light Brass 80 mm)
   * XT30 power cable, suitable capacitor, and 4S battery
   * Propellers, supplied mounting screws, silicone dampers, TPU washers
@@ Line 19: / Line 24: @@
 ===== 1. Prepare the Naked GoPro MAX 2 =====
 ==== 1.1 Disassemble the MAX 2 safely ====
+Read the [[https://wiki.fpvframe.ch/internal:nakedgopromax2|Naked GoPro MAX 2 manual]] and watch the [[https://youtu.be/bufcRK0GVz4|teardown video]] before opening the camera. Follow the teardown sequence to remove the mainboard and lens modules. Keep the three original lens screws for step 1.6.
-  * Follow the [[https://wiki.fpvframe.ch/internal:nakedgopromax2|Naked GoPro MAX 2 manual]] and watch the [[https://youtu.be/bufcRK0GVz4|MAX 2 teardown video]] before opening the camera.
-  * Remove the mainboard and lens assembly only as described in the dedicated teardown guide.
-  * Keep the two fragile lens ribbon cables flat, supported and protected throughout the build.
-  * Also keep the 3 original lens Screws. You will need them later for the lens adapter
-**IMPORTANT:** Do not pull on the lens ribbon cables to lift or separate the lens modules.
 ==== 1.2 Prepare the GoPro mainboard mount ====
 {{:public:omnix_9.jpg?600|}}
 {{:public:omnix_10.jpg?600|}}
   * Place the GoPro mainboard into its printed mainboard mount, keeping all connectors accessible.
-  * Align the upper corners and secure them with **2x 1.4x3mm self-drilling screws**.
+  * Align the upper corners and secure them with **2 × 1.4 × 3 mm self-drilling screws**.
+==== 1.3 Position the GoPro flat cable ====
-==== 1.3 Position the GoPro flat cable ====
 {{:public:omnix_11.jpg?600|}}
+Route the mainboard ribbon cable as shown, leaving a gentle bend. Align each mating connector before seating it. Leave the display connector accessible if you plan to use a display later.
-  * Guide the flat cable in the direction shown, without folding or sharply bending it.
+==== 1.4 Install the mainboard top plate ====
-  * Align the ribbon cable and gently press them into the connectors.
-  * The free connector from the ribbon cable is to connect the display later if you need to.
-**IMPORTANT:** Never force a ribbon cable to much.
-==== 1.4 Install the mainboard top plate ====
 {{:public:omnix_12.jpg?600|}}
   * Fit the printed GoPro Mainboard Top Plate over the mainboard.
-  * Secure it with **5x 1.4x5mm self-drilling screws**.
+  * Secure it with **5 × 1.4 × 5 mm self-drilling screws**.
+==== 1.5 Connect the optional speaker ====
-==== 1.4.1 Connect speakers ====
 {{:public:omnix_360_new_new-1.jpg?600|}}
+If using the Flywoo GoPro speaker, connect its lead to the matching connector on the GoPro ribbon cable.
-  * Connect the flywoo Gopro speaker and connect the cable with the Gopro Ribbon cable
+==== 1.6 Fit the lens modules in the top adapter ====
-==== 1.5 Place the GoPro lens modules in the top adapter ====
 {{:public:omnix_8.jpg?600|}}
   * Position both GoPro lens modules in the printed Lens Adapter Top Mount.
   * Use the **3 original mini GoPro lens screws**; tighten lightly and evenly.
 **IMPORTANT:** The lens ribbons are the most delicate part of this build. Protect them from carbon edges and screw tips.
 ===== 2. Prepare the carbon frame and AIO =====
 ==== 2.1 Insert the four stack screws ====
 {{:public:omnix_1.jpg?600|}}
 {{:public:omnix_2.jpg?600|}}
   * Place the carbon top plate on a clean, stable assembly support.
-  * Insert **4x M2x16mm** stack screws part-way through the AIO mounting holes.
+  * Insert **4 × M2 × 16 mm** stack screws part-way through the AIO mounting holes.
-  * Use the **1.4mm TPU washers** to keep the screws in place.
+  * Use the **1.4 mm TPU washers** to keep the screws in place.
+==== 2.2 Fit the Flywoo AIO ====
-==== 2.2 Place the Flywoo AIO ====
 {{:public:omnix_3.jpg?600|}}
 {{:public:omnix_4.jpg?600|}}
@@ Line 87: / Line 82: @@
   * Use the side view to check that the AIO is supported evenly and sits above the carbon.
   * Orient the connectors so the later GoPro and DJI wiring can be routed without strain.
-  * Now its a good time to Coat the one side of the FC (not the side where you gonna soilder the motors on)
+  * If applying a protective coating, follow the coating instructions. Keep connectors and pads needed for soldering clear.
 ==== 2.3 Fit the upper TPU washers ====
 {{:public:omnix_5.jpg?600|}}
-  * Install the larger **2.8mm TPU washers** above the AIO.
+  * Install the larger **2.8 mm TPU washers** above the AIO.
   * Leave sufficient screw length and clearance for the Naked DJI O4 Pro stack above it.
 ==== 2.4 Mount the motors ====
 {{:public:omnix_ai1.jpeg?600|}}
+  * Install all four motors with **4 × M2 × 4 mm screws per motor**.
-  * Install all four motors with **4x M2x4mm screws per motor**.
   * Route the motor wires neatly along the X-shaped carbon arms toward the AIO.
   * Check that the mounting screws cannot reach the motor windings, and protect wires from sharp carbon edges.
 ===== 3. Fit the GoPro lens and mainboard assembly =====
 ==== 3.1 Mount the lens adapter in the carbon frame ====
 {{:public:omnix_18.jpg?600|}}
   * Align the prepared GoPro lens assembly with the circular opening in the carbon frame.
-  * Secure the adapter with **4x 1.4x4mm self-drilling screws**.
+  * Secure the adapter with **4 × 1.4 × 4 mm self-drilling screws**.
   * Confirm that the lens is centered and the lens ribbon cables have an unobstructed path.
 **IMPORTANT:** Do not trap a lens ribbon between the lens adapter and carbon plate.
+==== 3.2 Test-fit the GoPro mainboard mount ====
-==== 3.4 Install the Gopro Mainboard====
 {{:public:omnix_ai2.jpeg?600|}}
+Slide the mainboard mount beneath the lens assembly. Align its bracket with the center frame strut and keep both lens ribbons clear.
- * Carefully position the mainboard assembly around and beneath the lens module.
-  * Guide the mainboard mount into its location while keeping both lens ribbons free.
-  * Align the center frame strut with the mainboard bracket and confirm a flat fit.
 {{:public:omnix_23.jpg?600|}}
+Check that the mount sits flat and that the flat cable passes through its opening, clear of the crossbar. Hold the mount in its assembled position to measure the motor wires in step 4.1.
+===== 4. Wire the motors and power supply =====
-  * Secure the GoPro mainboard assembly with **4x 1.4x5mm self-drilling screws**.
+==== 4.1 Measure the motor wires ====
-  * Keep the flat cable in the designed opening; do not clamp it under the printed crossbar.
-  * Carefully connect both lens ribbons to the GoPro mainboard, fully seat them, and close their connector locks.
-  * Check the lens centering, he GoPro mainboard position and the free space around the camera.
-  * Identify the **white GoPro BEC / power board at the rear of the drone**. It powers the naked GoPro; do not confuse it with the XT30 connector or the flight controller.
-  * Keep the GoPro BEC connector and thin red/black supply wires accessible for the later power-routing steps.
-===== 4. Route and solder motor and XT30 power wiring =====
-==== Check the lenght for the motor cables ====
 {{:public:omnix_ai2.jpeg?600|}}
+Route the motor wires through the channels under the printed GoPro mainboard mount. Identify the motor pads on your AIO revision. Mark each wire where it reaches its pad without tension, then remove the GoPro assemblies from the soldering area before trimming the wires.
+==== 4.2 Solder the motor wires ====
-  * Make sure the motor cables go nicley under the Peinted Gopro Mainboard adapter.
+{{:public:omnix_360_new_-10.jpg?600|}} {{:public:omnix_360_new_-9.jpg?600|}}
-  * Now you can cut the lenght for the Motors
+Strip about 2 mm of insulation from each motor wire. Twist and tin the wire ends, tin the corresponding motor pads, then solder each wire to its pad. Check the joints for bridges.
-==== 4.2 Prepare and solder the AIO pads ====
-{{:public:omnix_360_new_-10.jpg?600|}}
-{{:public:omnix_360_new_-9.jpg?600|}}
-  * Temporarily remove the GoPro camera assembly before soldering to protect it from heat, solder and flux.
+==== 4.3 Fit the XT30 and GoPro BEC ====
-  * Cut wires to length, strip roughly **2mm**, twist and pre-tin the wire ends.
-  * Pre-tin the correct motor and battery pads on the AIO, then solder the wires to their assigned pads.
-  * Follow the AIO manufacturer pinout for this exact board revision; verify **XT30 polarity** before applying power.
-**IMPORTANT:** Do not copy pad assignments blindly from a photograph if your Flywoo AIO revision differs.
-==== 4.4 Install the XT 30  ====
 {{:public:omnix_360_new_-4.jpg?600|}}
+Clip the XT30 into its printed mount. Fit the GoPro BEC into its holder with two M1.4 × 4 mm screws so you can measure the power leads in their installed positions.
-  * Clip the XT 3O in the 3d Mount
+==== 4.4 Position the capacitor and measure the power leads ====
-  * to ensuure to get the right cable lenght of the XT 30 to the capicator we reeccomend to in stall the Gopro bec.  Just Put the Gopro Bec into the 3d Mount for it with 2 m1,4mm x 4.
-==== 4.4 Install the Capacitor and Cut the wires   ====
 {{:public:omnix_360_new_-6.jpg?600|}}
+Secure the capacitor standoff with one M2 × 5 mm screw and fit the capacitor in its printed holder. Temporarily invert it as shown to measure the XT30 leads and the two leads to the AIO. Before cutting, check that all leads will reach their terminals when the capacitor is turned back into place.
+==== 4.5 Solder and insulate the power connections ====
+{{:public:omnix_360_new_-11.jpg?600|}} {{:public:omnix_360_new_-12.jpg?600|}}
+Turn the capacitor assembly into the soldering position shown, with the Flywoo logo facing you. Identify positive and negative from the terminal markings. Verify the capacitor rating, GoPro BEC input rating and wiring diagram for your hardware before soldering.
-  * Mount the Stanodd woth. a m2x5mm and attach the Capacitor wwith the 3d mount for it
+Route the GoPro BEC power lead around the XT30 lead as shown. Solder the XT30 leads, AIO battery leads and BEC input leads to their verified connections. Solder the AIO ends to the corresponding battery pads. Inspect every joint and check polarity from the XT30 through to the AIO and BEC.
-  * Put it uoside down first to make sure you cut the wire the righ lenght
-  * The 2 cables attached toi the capcaitor are going to the FC you can also short them to the right kenght now
-==== 4.4 Soilder the Capacitor ====
-{{:public:omnix_360_new_-11.jpg?600|}}
-{{:public:omnix_360_new_-12.jpg?600|}}
-  * Now Turn the capacitor around for soildering
-  * Make sure the Flywoo Logo looks to you like in the Picture
-  * You can now soilder on all the Cable the cables
-  * 1. Going to the XT 30
-  * 2.Going to the FC
-  * 3. Gopro BEC Power cable ( Make sure you wrap it around the Xt 30 cable like shown on the Picture
-  * Always make sure that after turning around the capactir at the end the cables are not gonna be wired
 {{:public:omnix_360_new_-13.jpg?600|}}
+Insulate the exposed joints. If using a liquid insulating coating, follow its application and curing instructions.
-  * Now you can Put some plastic dip on it
 {{:public:omnix_360_new_-14.jpg?600|}}
+Return the capacitor to its installed position. Check that the leads lie clear of the frame edges and that turning the holder has not twisted the wires or pulled on a joint.
-  * Turn the Capacitor around and lay the cables nicely down y
+===== 5. Reinstall the GoPro mainboard =====
+{{:public:omnix_360_new_-16.jpg?600|}} {{:public:omnix_360_new_-17.jpg?600|}}
+Refit the lens assembly removed for soldering as described in step 3.1. Return the mainboard mount to the position checked in step 3.2. Seat the motor wires in the printed channels and keep both lens ribbons clear of the crossbar and fasteners.
+**Verify the mainboard mount screws before tightening.** The build notes specify four 1.4 × 5 mm self-drilling screws for this mount but also mention 1.4 × 4 mm screws at reassembly. Confirm the correct length for your frame revision and check clearance at each screw tip. Secure the mount from the top of the frame, then carefully seat both lens ribbons and close any connector latches.
+===== 6. Prepare the ELRS receiver =====
+{{:public:omnix_39.jpg?600|}} {{:public:omnix_40.jpg?600|}}
+Connect the receiver harness to the ELRS receiver according to its pinout. Seat the compatible T-style antenna connector and fit the receiver in its printed holder. Before installing the O4 Pro above the AIO, complete any soldering needed for the receiver, optional GPS or fan while the pads are accessible. Verify the supply voltage, ground and signal connections for each installed module against its documentation and the AIO pinout.
+===== 7. Install the naked DJI O4 Pro =====
+==== 7.1 Prepare the naked O4 electronics ====
+{{:public:omnix_37.jpg?600|}} {{:public:omnix_38.jpg?600|}}
+Prepare the O4 Pro using the instructions for your [[https://www.skkyfpv.com/|skkyFPV naked kit]]. Inspect the camera cable and the harness to the flight controller. The reference build uses short cables for both connections.
-===== 5. Install and insulate the capacitor =====
+**Fit compatible video antennas before applying power to the O4 Pro.**
-==== Install the Mainboard again  ====
-{{:public:omnix_360_new_-16.jpg?600|}}
-{{:public:omnix_360_new_-17.jpg?600|}}
-  * Now you can put the Mainboard back in again
+==== 7.2 Install the naked O4 Pro above the AIO ====
-  * Make sure now you donw squish any cables especially the camera Lens cable
-  * YOu can thighten it again with hte m 1.4 4xmm from the Top side of the frame
-  * Check that all the Motor cables are nicely layout in the 3d part channel
-  * Attach the lens cable with Gorpo carefully
-  *
-===== 7. Prepare and mount the ELRS receiver =====
-==== 7.1 Prepare the receiver and antenna ====
-{{:public:omnix_39.jpg?600|}}
-{{:public:omnix_40.jpg?600|}}
-  * Use the receiver module and T-style receiver antenna shown in the photographs.
-  * Connect or solder the receiver wires, then fit the module securely into its printed holder.
-  * Confirm the antenna connection is properly seated and not sharply bent.
-===== 8. Prepare the Naked DJI O4 Pro =====
-==== 8.1 Prepare the naked O4 electronics ====
-{{:public:omnix_37.jpg?600|}}
-{{:public:omnix_38.jpg?600|}}
-  * Prepare the O4 Pro according to the [[https://www.skkyfpv.com/|skkyFPV]] naked kit instructions.
-  * Check the camera ribbon, VTX board and short AIO connector cable.
-  * We reccomend to use a short DJI Camera Connection cables as well as a short cable to connect to the FC
-**IMPORTANT:** Always connect suitable VTX antennas before powering the DJI O4 Pro.
-==== 8.2 Install the naked O4 Pro above the AIO ====
 {{:public:omnix_42.jpg?600|}}
 {{:public:omnix_43.jpg?600|}}
@@ Line 251: / Line 184: @@
   * Connect the O4 Pro to the correct FC/VTX connector and check cable clearance around USB and other ports.
-==== 8.3 Install the DJI Antennas ====
+==== 7.3 Fit the video antennas ====
-{{:public:omnix_44.jpg?600|}}
-{{:public:omnix_360_-3.jpg?600|}}
-{{:public:omnix_360_-4.jpg?600|}}
+{{:public:omnix_44.jpg?600|}} {{:public:omnix_360_-3.jpg?600|}} {{:public:omnix_360_-4.jpg?600|}}
+Seat the O4 Pro antenna connectors and secure the antennas in the printed adapters on either side of the frame. The reference build recommends Flywoo 5.8 GHz Light Brass 80 mm antennas to save weight.
-  * Click in the DJI o4 Pro Antennas
+===== 8. Install the O4 Pro camera and ELRS receiver =====
-  * For lower weight, the original build recommends **Flywoo 5.8GHz Light Brass 80mm antennas**.
-  * Install the woth the ED printed adapter on both sides like shown on the Picture
+==== 8.1 Install the front standoffs ====
-===== 9. Install the O4 Pro camera and Reciver =====
-==== 9.1 Install the front standoffs ====
 {{:public:omnix_46.jpg?600|}}
+  * Install the two front standoffs with **2 × M2 × 5 mm** screws.
-  * Install the two front standoffs with **2x M2x5mm** screws.
+==== 8.2 Fit the receiver and camera ====
-==== 9.2 Fit the O4 Pro camera  / Reciver====
+{{:public:omnix_48.jpg?600|}} {{:public:omnix_51.jpg?600|}}
-{{:public:omnix_48.jpg?600|}}
+Fit the prepared receiver holder on one front standoff and the matching printed camera support on the other. Place the O4 Pro camera **upside down** between the supports and secure it with two M2 × 5 mm screws. Connect the camera cable and route it in gentle curves with enough slack to close the frame.
-{{:public:omnix_51.jpg?600|}}
-  * INstall the reciver which you prepared before
+==== 8.3 Route the receiver antenna ====
-  * Install the Second * Printed oart on the other standoff
-  * Mount the Naked O4 Pro camera with **2x M2x5mm** screwsinbetween
-  * For this OMNIX design, mount the O4 Pro camera **upside down** for the top-plate layout.
-  * Route the camera ribbon carefully with gentle curves and enough slack for assembly.
-==== 9.3 Place the Reciver antennas ====
+{{:public:omnix_52.jpg?600|}} {{:public:omnix_63.jpg?600|}}
-{{:public:omnix_52.jpg?600|}}
+Route the arms of the receiver antenna into the rear or side holders as shown. Keep the antenna clear of the propellers.
-{{:public:omnix_63.jpg?600|}}
-  * Fit the Reciver antennas in their printed rear/side antenna holders as pictured.
+===== 9. Optional GPS module =====
+==== 9.1 Prepare the GPS wiring ====
-===== 10. Optional GPS module =====
-==== 10.1 Prepare GPS and receiver wiring ====
 {{:public:omnix_56.jpg?600|}}
@@ Line 300: / Line 216: @@
   * Confirm the pin labels on the specific GPS module and AIO board before connection; do not rely on wire color alone.
-==== 10.2 Check the GPS cable connection and position ====
+==== 9.2 Check the GPS cable connection and position ====
 {{:public:omnix_54.jpg?600|}}
@@ Line 307: / Line 224: @@
   * Leave enough slack to close the bottom plate without trapping the wires.
-==== 10.3 Mount the GPS module ====
+==== 9.3 Mount the GPS module ====
 {{:public:omnix_56.jpg?600|}}
@@ Line 313: / Line 231: @@
   * Check that the GPS antenna side marked **THIS SIDE UP** faces outward/upward as intended.
   * Configure the GPS protocol, UART and baud rate later in Betaflight.
-  * Use M1.4 4mm screws
+  * Secure the GPS mount with M1.4 × 4 mm screws.
-===== 11. Close the frame =====
-==== 11.1 Connect the Gopro Bec an Gopro Power Cable  ====
+===== 10. Close the frame =====
-  * Connect the Gopro BEc with THe Gopro Ribbon
+==== 10.1 Connect the GoPro BEC ====
-  * COnnect THe POwer cable forom the GorpoBEc
+Connect the GoPro BEC to the matching GoPro ribbon connector. Plug the power lead prepared in step 4.5 into the BEC after verifying its polarity.
+==== 10.2 Fit the bottom lens adapter and close the frame ====
-==== 11.2 Prepare the bottom carbon plate ====
 {{:public:omnix_55.jpg?600|}}
 {{:public:omnix_57.jpg?600|}}
-  * Install the remaining **6 outer standoffs** using **6x M2x5mm** screws.
+  * Install the remaining **6 outer standoffs** using **6 × M2 × 5 mm** screws.
   * Position the GoPro Lens Adapter Bottom on the bottom carbon plate.
-  * Secure the bottom adapter with **4x 1.4x4mm self-drilling screws**.
+  * Secure the bottom adapter with **4 × 1.4 × 4 mm self-drilling screws**.
-==== 11.3 Install the bottom plate ====
-{{:public:omnix_58.jpg?600|}}
-{{:public:omnix_59.jpg?600|}}
   * Align the top and bottom carbon plates carefully.
   * Confirm that no power cable, motor wire or fragile GoPro lens ribbon is between the two plates.
-  * Secure the bottom plate with **12x M2x5mm screws** and inspect all gaps.
+  * Secure the bottom plate with **12 × M2 × 5 mm screws** and inspect all gaps.
 **IMPORTANT:** If the frame does not sit flat, stop and find the trapped part or cable before tightening.
+===== 11. Perform the electrical checks with the propellers removed =====
-===== 12. Electrical checks - NO PROPELLERS =====
+==== 11.1 Inspect power, connectors and motor direction ====
-==== 12.1 Inspect power, connectors and motor direction ====
-{{:public:omnix_54.jpg?600|}}
+**Provide airflow over the naked GoPro and O4 Pro during powered bench tests.**
-{{:public:omnix_71.jpg?600|}}
-  * **Remove all propellers** before electrical testing.
+* **Remove all propellers** before electrical testing.
   * Check solder joints, XT30 polarity, capacitor polarity and the GoPro BEC positive/negative wires.
   * Use a multimeter to check for shorts and a **smoke stopper** on first power-up.
@@ Line 354: / Line 266: @@
   * Configure and verify motor order and direction in Betaflight with no propellers attached.
-==== 12.2 Inspect GoPro lens imaging and stitching ====
+===== 12. Test the GoPro recording and stitching =====
-{{:public:omnix_18.jpg?600|}}
-  * Power the naked MAX 2 through the **rear GoPro BEC** and confirm that **both lenses** record correctly.
-  * Shoot a stationary 360 test with objects crossing the stitch line, then repeat with the camera rotated.
-  * If the stitch does not align, inspect lens centering, lens mounting positions and flex seating; a QR code does **not** physically calibrate a misaligned lens assembly.
-**IMPORTANT:** Operate naked O4/GoPro electronics with suitable airflow; avoid prolonged stationary power-up.
+==== 12.2 Check both lenses and the stitch line ====
-===== 13. GoPro MAX 2 test filming QR code =====
+Power the MAX 2 through the rear GoPro BEC and record a short stationary 360° clip with an object crossing the stitch line. Rotate the camera and repeat. Play back both clips. Confirm that both lenses contribute an image and that the object lines up across the seam. If it does not, disconnect power and check lens centering, mount alignment and ribbon seating. Recording settings cannot correct mechanical misalignment.
-==== 13.1 Scan the test recording preset ====
-{{:public:omnix_81.png?600|}}
-  * Install the **GoPro Labs firmware for MAX2** before using Labs QR configuration.
+===== 13. Install propellers and complete final inspection =====
-  * Point the MAX 2 at this QR code before the short test recording. This QR **sets settings only**; start/stop recording normally.
-  * Target preset: **360 video, 8K/30fps, High bitrate, 10-bit, Medium sharpness, ISO 100-400, WB 5500K**.
-  * The QR additionally requests **200 Mbit/s** using the experimental Labs bitrate command; actual support/bitrate must be verified on the camera.
-  * In mixed or changing light, you may prefer Auto white balance/ISO adjustments after basic testing.
-  * Use [[https://gopro.github.io/labs/max2/|GoPro MAX2 QR Code Creator]] to adjust a preset if your MAX2 firmware rejects any setting.
-**IMPORTANT:** This is a newly generated test QR based on documented Labs commands, not the original image from a prior conversation and not yet verified on a physical MAX2. It will not fix lens-calibration or stitching geometry.
+==== 13.1 Install and check propellers ====
-The QR command encoded above is: **%%m3mVr8p30b1d10sMi4M1w55$BITR=200%%**
+* After all electrical checks pass, disconnect the battery and mount all four propellers.
+  * Use **2 × M2 × 7 mm screws per propeller** and follow the configured motor direction.
-===== 14. Install propellers and complete final inspection =====
-==== 14.1 Install and check propellers ====
-  * After all electrical checks pass, disconnect the battery and mount all four propellers.
-  * Use **2x M2x7mm screws per propeller** and follow the configured motor direction.
   * Rotate each propeller by hand and confirm complete clearance from the frame, ribbons, antenna wires and power leads.
-==== 14.2 Final checks before the first flight ====
+==== 13.2 Final checks before the first flight ====
-  * Check all screws, frame standoffs and motor fasteners.
-  * Confirm both MAX 2 lenses are centered, covered for transport and show matching 360 footage.
+* Check all screws, frame standoffs and motor fasteners.
+  * Check that both MAX 2 lenses are centered. Fit their covers for transport and remove them before filming.
   * Confirm the **white rear GoPro BEC**, capacitor, XT30 and wrapped thin GoPro BEC wires are firmly retained.
   * Confirm ELRS, GPS (if installed), O4 Pro video, antennas and battery mounting.
   * Measure the final take-off weight with the selected battery and perform a controlled first hover test.
+==== 13.3 Use Gopro Preset  ====
+{{:public:img_8589.jpg?600|}}
+  * Following Setting
+  * 8k 30 FPS
+  * ISO 100-400
+  * Bitrate High
+  * Sharpness MEdium
+  * Color Normal
+  * Shutter Auto
+  * TUSB
 ===== Troubleshooting =====
-  * **GoPro not powering on:** inspect the rear white GoPro BEC, power polarity and ribbon/power connectors.
+Disconnect power before inspecting solder joints or reseating connectors.
+* **GoPro not powering on:** inspect the rear white GoPro BEC, power polarity and ribbon/power connectors.
   * **One GoPro lens missing / unstable image:** carefully inspect and re-seat both very fragile lens ribbon cables; check connector locks.
   * **Stitching mismatch:** verify lens adapter centering, housing geometry, matching focus/position and identical lens assembly alignment; Labs recording settings cannot repair physical misalignment.
@@ Line 402: / Line 322: @@
 ===== References =====
-  * [[https://wiki.fpvframe.ch/internal:nakedgopromax2|Naked GoPro MAX 2 Manual]]
+* [[https://wiki.fpvframe.ch/internal:nakedgopromax2|Naked GoPro MAX 2 Manual]]
   * [[https://youtu.be/bufcRK0GVz4|MAX 2 Teardown Video]]
   * [[https://gopro.github.io/labs/max2/|Official GoPro MAX2 Labs QR Creator]]
   * [[https://gopro.github.io/labs/control/settings/|GoPro Labs QR Command Reference]]
   * [[https://gopro.github.io/labs/|GoPro Labs Firmware]]