public:cinematix35
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| public:cinematix35 [2026/01/19 08:43] – [Step 5 – TPU Bumpers] laurin | public:cinematix35 [2026/01/19 08:49] (current) – laurin | ||
|---|---|---|---|
| Line 17: | Line 17: | ||
| • Start with the top plate | • Start with the top plate | ||
| + | |||
| • Ensure the threaded inserts are facing upward | • Ensure the threaded inserts are facing upward | ||
| Line 23: | Line 24: | ||
| • Mount the AIO flight controller beneath the TPU capacitor mount | • Mount the AIO flight controller beneath the TPU capacitor mount | ||
| + | |||
| • Secure using M2x15 mm screws | • Secure using M2x15 mm screws | ||
| Line 29: | Line 31: | ||
| • Install the TPU RX mount | • Install the TPU RX mount | ||
| + | |||
| • Secure with M2x4 mm screws | • Secure with M2x4 mm screws | ||
| Line 35: | Line 38: | ||
| • Install the TPU mount for your DJI VTX | • Install the TPU mount for your DJI VTX | ||
| + | |||
| • Secure using M2x6 mm screws | • Secure using M2x6 mm screws | ||
| Line 41: | Line 45: | ||
| • Insert M2x8 mm screws through the TPU bumpers | • Insert M2x8 mm screws through the TPU bumpers | ||
| + | |||
| • Mount the bumpers onto the prop guards as shown | • Mount the bumpers onto the prop guards as shown | ||
| Line 47: | Line 52: | ||
| • Install M2x25 mm standoffs onto the exposed screws | • Install M2x25 mm standoffs onto the exposed screws | ||
| + | |||
| • Add two additional standoffs using M2x6 mm screws: | • Add two additional standoffs using M2x6 mm screws: | ||
| – Where the prop guards meet | – Where the prop guards meet | ||
| – At the rear of the top plate | – At the rear of the top plate | ||
| + | |||
| • Follow the reference image carefully | • Follow the reference image carefully | ||
| Line 56: | Line 63: | ||
| • Insert two M2x10 mm screws into the front holes of the TPU GoPro mount | • Insert two M2x10 mm screws into the front holes of the TPU GoPro mount | ||
| + | |||
| • Install the mount on the frame | • Install the mount on the frame | ||
| + | |||
| • Secure the rear (pointed side) with one M2x6 mm screw | • Secure the rear (pointed side) with one M2x6 mm screw | ||
| Line 63: | Line 72: | ||
| • Push the TPU camera mounts onto the front standoffs | • Push the TPU camera mounts onto the front standoffs | ||
| + | |||
| • Ensure correct orientation as shown above | • Ensure correct orientation as shown above | ||
| Line 74: | Line 84: | ||
| • Install four M2x25 mm standoffs using M2x6 mm screws | • Install four M2x25 mm standoffs using M2x6 mm screws | ||
| + | |||
| • Push the TPU side covers into place | • Push the TPU side covers into place | ||
| + | |||
| • These side covers also retain the DJI VTX antenna | • These side covers also retain the DJI VTX antenna | ||
| Line 81: | Line 93: | ||
| • Install the TPU bumpers on the bottom plate | • Install the TPU bumpers on the bottom plate | ||
| + | |||
| • Use M2x8 mm screws, same as on the top plate | • Use M2x8 mm screws, same as on the top plate | ||
| Line 87: | Line 100: | ||
| • Join both frame halves together | • Join both frame halves together | ||
| + | |||
| • Use: | • Use: | ||
| – M2x8 mm screws in the front and rear standoffs | – M2x8 mm screws in the front and rear standoffs | ||
| Line 94: | Line 108: | ||
| {{ : | {{ : | ||
| - | 🔁 Flip the frame over — and voilà! | + | Flip the frame over — and voilà! |
| - | Your CinematiX 35 Frame is now fully assembled and ready for electronics installation. | + | Your CinematiX 35 Frame is now fully assembled and ready for electronics installation. |
public/cinematix35.1768812235.txt.gz · Last modified: by laurin