Differences

This shows you the differences between two versions of the page.

--- public:cinematix35 [2026/01/16 12:58] – laurin
+++ public:cinematix35 [2026/01/19 08:49] (current) – laurin
@@ Line 1: / Line 1: @@
-====== CinematiX 35 Frame build manual ======
+====== CinematiX 35 Frame Build Manual ======
-====Top Plate====
+===== Introduction =====
+{{ :public:cx35_frame_manual-1.jpg?nolink&600 |}}
+Welcome to the CinematiX 35 Frame Build Manual.
+This guide will walk you through the complete assembly process step by step.
+**Note:
+**The CinematiX 35 can be built in either Pusher configuration (motors facing down) or Puller configuration.
+In this manual, we are building the Pusher configuration, as it provides improved thrust and efficiency.
+➡️ To build the Puller configuration, simply swap the top and bottom plates.
+===== Step 1 – Top Plate =====
 {{ :public:cx35_frame_manual-26.jpg?nolink&600 |}}
-Start with the top Plate. The Thread insert should look upwards.
-====TPU Capacitor Mount====
+• Start with the top plate
-{{ :public:cx35_frame_manual-25.jpg?nolink&600 |}}
-The AIO FC is mounted beneath the TPU Capacitor mount with M2x15mm screws.
-====TPU RX Mount====
+• Ensure the threaded inserts are facing upward
+===== Step 2 – TPU Capacitor Mount =====
+{{ :public:cx35_frame_manual-15.jpg?nolink&600 |}}
+• Mount the AIO flight controller beneath the TPU capacitor mount
+• Secure using M2x15 mm screws
+===== Step 3 – TPU RX Mount =====
 {{ :public:cx35_frame_manual-16.jpg?nolink&600 |}}
-Install the TPU RX Mount with M2x4mm Screws.
-====TPU VTX Mount====
+• Install the TPU RX mount
+• Secure with M2x4 mm screws
+===== Step 4 – TPU VTX Mount =====
 {{ :public:cx35_frame_manual-15.jpg?nolink&600 |}}
-Install the TPU Mount for your DJI VTX with M2x6mm Screws.
-====TPU Bumper====
+• Install the TPU mount for your DJI VTX
-{{ :public:cx35_frame_manual-17.jpg?nolink&600 |}}
-Prepare the TPU Bumpers by sticking M2x8mm Screws through them and mounting them on the Propguards.
-====Standoffs====
+• Secure using M2x6 mm screws
+===== Step 5 – TPU Bumpers =====
+{{ :public:cx35_frame_manual-3.jpg?nolink&600 |}}
+• Insert M2x8 mm screws through the TPU bumpers
+• Mount the bumpers onto the prop guards as shown
+===== Step 6 – Standoffs =====
 {{ :public:cx35_frame_manual-14.jpg?nolink&600 |}}
-Screw on M2x25mm Standoffs on the exposed screws. also add two Standoffs with M2x6mm Screws where the propguards touch and in the rear of the top Plate as shown above.
-====TPU GoPro Mount====
+• Install M2x25 mm standoffs onto the exposed screws
+• Add two additional standoffs using M2x6 mm screws:
+– Where the prop guards meet
+– At the rear of the top plate
+• Follow the reference image carefully
+===== Step 7 – TPU GoPro Mount =====
 {{ :public:cx35_frame_manual-13.jpg?nolink&600 |}}
-Stick two M2x10mm Screws through the two front holes of the TPU GoPro Mount and install it on the Frame. On the rear end (pointy side) use a M2x6mm screw.
-====TPU Camera Mount====
+• Insert two M2x10 mm screws into the front holes of the TPU GoPro mount
+• Install the mount on the frame
+• Secure the rear (pointed side) with one M2x6 mm screw
+===== Step 8 – TPU Camera Mount =====
 {{ :public:cx35_frame_manual-10.jpg?nolink&600 |}}
-Push the TPU Camera Mounts on the front end standoffs as shown above.
-====TPU Bumper====
+• Push the TPU camera mounts onto the front standoffs
+• Ensure correct orientation as shown above
+===== Step 9 – TPU RX Antenna Mount =====
 {{ :public:cx35_frame_manual-9.jpg?nolink&600 |}}
+• Push the TPU RX antenna mount onto the rear standoffs
+===== Step 10 – TPU VTX Antenna Mount & Side Covers =====
+{{ :public:cx35_frame_manual-5.jpg?nolink&600 |}}
+• Install four M2x25 mm standoffs using M2x6 mm screws
+• Push the TPU side covers into place
+• These side covers also retain the DJI VTX antenna
+===== Step 11 – TPU Bumper Bottom Plate =====
+{{ :public:cx35_frame_manual-4.jpg?nolink&600 |}}
+• Install the TPU bumpers on the bottom plate
+• Use M2x8 mm screws, same as on the top plate
+===== Step 12 – Frame Assembly =====
+{{ :public:cx35_frame_manual-2.jpg?nolink&600 |}}
+• Join both frame halves together
+• Use:
+– M2x8 mm screws in the front and rear standoffs
+– M2x6 mm screws in the standoffs holding the TPU side covers
+===== Finish =====
+{{ :public:cx35_frame_manual-1.jpg?nolink&600 |}}
+Flip the frame over — and voilà!
+Your CinematiX 35 Frame is now fully assembled and ready for electronics installation.