FPVFrame.ch

User Tools

Site Tools

Trace: • nakex25v2
public:nakex25v2

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
public:nakex25v2 [2026/02/11 10:04] – laurinpublic:nakex25v2 [2026/02/11 13:40] (current) – [Step 29 – Battery Pads] laurin
Line 79: Line 79:
  
 • Install the standoffs onto the top plate • Install the standoffs onto the top plate
 +
 • Secure using M2x6 mm screws • Secure using M2x6 mm screws
  
Line 85: Line 86:
  
 • Install all motors • Install all motors
 +
 • Secure with M2x5 mm screws • Secure with M2x5 mm screws
  
Line 91: Line 93:
  
 • Apply conformal coating to the bottom side of the flight controller • Apply conformal coating to the bottom side of the flight controller
-• Only do this if you do not plan to solder anything else on that side 
  
-Note: +• Only do this if you do not plan to solder anything additional like GPS or LEDs on that side 
-If you are using the Flywoo Goku GN745 (recommended), this step is not required.+ 
  
 Tip: Tip:
Line 104: Line 106:
  
 • Mount the FC using M2x12 mm screws • Mount the FC using M2x12 mm screws
 +
 • Use the spacers supplied with the FC • Use the spacers supplied with the FC
 +
 • Ensure 1–2 mm clearance between the FC and the carbon plate • Ensure 1–2 mm clearance between the FC and the carbon plate
  
Line 112: Line 116:
  
 Soldering setup: Soldering setup:
 +
 • Temperature: 450 °C • Temperature: 450 °C
-• Solder: TBS solder+ 
 +• Solder: TBS solder (recommended)
  
 ===== Step 5 – Motor Wire Preparation ===== ===== Step 5 – Motor Wire Preparation =====
Line 119: Line 125:
  
 • Cut motor wires to length • Cut motor wires to length
 +
 • Ideal length: about mid-FC position when routed straight along the arms • Ideal length: about mid-FC position when routed straight along the arms
 +
 • Leave a little slack to protect pads in a crash • Leave a little slack to protect pads in a crash
  
 • Strip approx. 2 mm insulation • Strip approx. 2 mm insulation
 +
 • Twist and pre-tin the wire ends • Twist and pre-tin the wire ends
  
Line 129: Line 138:
  
 • Tape the motor wires neatly to the frame • Tape the motor wires neatly to the frame
 +
 • Solder the wires to the ESC pads • Solder the wires to the ESC pads
  
Line 135: Line 145:
  
 • Trim capacitor legs to approx. 3 mm • Trim capacitor legs to approx. 3 mm
 +
 • Solder 20 AWG wires to the legs • Solder 20 AWG wires to the legs
 +
 • Polarity: • Polarity:
 +
 – Short leg = – – Short leg = –
 +
 – Long leg = + – Long leg = +
 +
 • Insulate connections using shrink tube • Insulate connections using shrink tube
  
Line 145: Line 160:
  
 • Solder the capacitor to the FC power pads • Solder the capacitor to the FC power pads
 +
 • Align it straight and centered on the plate, as shown • Align it straight and centered on the plate, as shown
  
Line 151: Line 167:
  
 • Solder 16 AWG power wires to the FC • Solder 16 AWG power wires to the FC
 +
 • Length should be slightly longer than the frame • Length should be slightly longer than the frame
  
Line 158: Line 175:
  
 • Cut the Naked Action Cam power wire to 10–11 cm • Cut the Naked Action Cam power wire to 10–11 cm
 +
 • Solder it to the FC power pads • Solder it to the FC power pads
  
Line 166: Line 184:
  
 • Apply conformal coating to the top side of the FC • Apply conformal coating to the top side of the FC
 +
 • Avoid all connectors and buttons • Avoid all connectors and buttons
  
Line 182: Line 201:
  
 • Cut power wires to length • Cut power wires to length
 +
 • Solder them to the XT30 connector • Solder them to the XT30 connector
  
Line 193: Line 213:
  
 • Cut receiver wires to approx. 5 cm • Cut receiver wires to approx. 5 cm
 +
 • Solder the wires • Solder the wires
 +
 • Bend the antenna slightly • Bend the antenna slightly
 +
 • Cover everything with shrink tube • Cover everything with shrink tube
 +
 • Ensure the bind button remains accessible • Ensure the bind button remains accessible
  
 ===== Step 17 – Receiver Installation ===== ===== Step 17 – Receiver Installation =====
-{{:public:nakex_2.5_diy_buildmanual-43.jpg?nolink&400|}}{{ :public:nakex_2.5_diy_buildmanual-38.5.png?nolink&400|}}+{{ :public:nakex_2.5_diy_buildmanual-43.jpg?nolink&600 |}}
  
 • Install the receiver • Install the receiver
 +
 • Apply shrink tube over: • Apply shrink tube over:
 +
 – Capacitor – Capacitor
 +
 – Power wires – Power wires
 +
 – Receiver – Receiver
 +
 +• Alternatively to shrinktube, tape can be used. If you decide to do this, wait until the VTX antennas are installed.
 +
 • Secure the assembly by screwing in the XT30 PCB plate • Secure the assembly by screwing in the XT30 PCB plate
  
Line 212: Line 243:
  
 • Install the TPU VTX mount on the DJI O4 / O3 air unit • Install the TPU VTX mount on the DJI O4 / O3 air unit
 +
 • Use M2x4 mm screws • Use M2x4 mm screws
  
Line 220: Line 252:
  
 ===== Step 20 – O4 Antenna Modification ===== ===== Step 20 – O4 Antenna Modification =====
-{{ :public:nakex_2.5_diy_buildmanual-47.jpg?nolink&600 |}} 
  
-• Remove the four screws from the O4 air unit 
  
 {{ :public:nakex_2.5_diy_buildmanual-49.jpg?nolink&600 |}} {{ :public:nakex_2.5_diy_buildmanual-49.jpg?nolink&600 |}}
 +
 +• Remove the four screws from the O4 air unit
  
 • Carefully lift the cover • Carefully lift the cover
 +
 • Remove the U.FL antenna connectors • Remove the U.FL antenna connectors
  
Line 234: Line 267:
 {{ :public:nakex_2.5_diy_buildmanual-51.jpg?nolink&600 |}} {{ :public:nakex_2.5_diy_buildmanual-51.jpg?nolink&600 |}}
  
-• Push the antennas through the shrink tube+• Push the antennas through the TPU mount and shrink tube 
 • Using pliers to gently open space can help • Using pliers to gently open space can help
  
Line 241: Line 275:
  
 • Reconnect the antennas • Reconnect the antennas
 +
 • Reinstall and secure the O4 top cover • Reinstall and secure the O4 top cover
  
Line 252: Line 287:
  
 • Install the O4 camera into the TPU camera mount • Install the O4 camera into the TPU camera mount
 +
 • Use a zip tie to shorten excess cable for a clean layout • Use a zip tie to shorten excess cable for a clean layout
  
Line 263: Line 299:
  
 • Install the CFK bottom plate using M2x6 mm screws • Install the CFK bottom plate using M2x6 mm screws
 +
 • Route the receiver antenna between the rear standoffs • Route the receiver antenna between the rear standoffs
  
Line 274: Line 311:
  
 • Install the TPU action cam mount • Install the TPU action cam mount
 +
 • Secure with M2x8 mm screws • Secure with M2x8 mm screws
  
Line 280: Line 318:
  
 • Cut battery pads into two thin, even strips • Cut battery pads into two thin, even strips
 +
 • Install lengthwise as shown • Install lengthwise as shown
  
 Benefits: Benefits:
 +
 ✔ Reduced weight ✔ Reduced weight
 +
 ✔ Excellent battery grip ✔ Excellent battery grip
 +
 ✔ Improved airflow to electronics ✔ Improved airflow to electronics
  
 +✔ Sexy
 ===== Finish ===== ===== Finish =====
 {{ :public:nakex_2.5_diy_buildmanual-62.jpg?nolink |}} {{ :public:nakex_2.5_diy_buildmanual-62.jpg?nolink |}}
Line 292: Line 335:
 Congratulations! Congratulations!
 The major build work is complete. The major build work is complete.
-All that’s left is Betaflight configuration and minor ESC setup — and your NakeX 2.5 is ready to fly+All that’s left is Betaflight configuration and minor ESC setup, install the props — and your NakeX 2.5 is ready to fly.
public/nakex25v2.1770804264.txt.gz · Last modified: by laurin
Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki