Differences

This shows you the differences between two versions of the page.

--- public:nakedtest [2023/12/19 21:57] – laurin
+++ public:nakedtest [2024/12/09 18:01] (current) – ↷ Page moved from internal:public:nakedtest to public:nakedtest admin
@@ Line 8: / Line 8: @@
 It's advisable to inspect and retighten all drone screws after the initial successful flights due to motor-induced vibrations. Regularly checking these screws ensures continual drone reliability.
+The O3 Air unit produces a lot of heat. Although actively cooled with a small fan, long term hovering or even standing can induce automatic power off due to heat limits of the O3 Air unit. Air stream during forward flight keeps the unit cool enough for reliable operation.
 Purchasing the BNFs with the InstantFly Kit includes the pre-mentioned procedures. However, going through these processes offers a comprehensive understanding and allows optional adjustments for personalized drone preferences. Our preset settings cater to beginners and experienced pilots, facilitating cinematic flying.
@@ Line 15: / Line 17: @@
 ==== Opening Procedure ====
-- Remove 4 horizontal screws (2 on each side).
+  * Remove 4 horizontal screws (2 on each side).
-- Remove 1 vertical screw from the back.
+  * Remove 1 vertical screw from the back.
-- Gently lift the canopy upwards, ensuring the antenna passes through the hole.
+  * Gently lift the canopy upwards, ensuring the antenna passes through the hole.
-- Disconnect the small antenna "plug" from the SMA connector.
+  * Disconnect the small antenna "plug" from the SMA connector.
 {{:public:rangex_pro_manual_1_compressed.jpeg}}
@@ Line 24: / Line 26: @@
 ==== Closing Procedure ====
-- Carefully place the canopy on the drone, ensuring the antenna passes through the hole.
+  * Carefully place the canopy on the drone, ensuring the antenna passes through the hole.
-- Check fitting on all sides. Ensure the motor and immortal T antenna wire snugly fit into the slots.
+  * Check fitting on all sides. Ensure the motor and immortal T antenna wire snugly fit into the slots.
-- Add 1 vertical screw to the back.
+  * Add 1 vertical screw to the back.
-- Add 4 horizontal screws (2 on each side).
+  * Add 4 horizontal screws (2 on each side).
-- Insert the small antenna "plug" into the SMA connector.
+  * Insert the small antenna "plug" into the SMA connector.
 ===== Binding your Remote Controller =====
-The RangeX Pro receiver arrives in bind mode. However, follow these steps:
+The RangeX Pro receiver arrives in bind mode. The button on the RX does not need to be pressed for initial binding, but here is the full procedure nevertheless:
-- Power on your transmitter.
+  * Power on your transmitter.
-- Enter Bind mode on your transmitter.
+  * Enter Bind mode on your transmitter.
-- Power up the drone's receiver. USB power might suffice, or connect the battery (without propellers).
+  * Power up the drone's receiver. USB power might suffice, or connect the battery (without propellers).
-- Press the bind button on the Crossfire receiver within 20s of powering the RX.
+  * Press the bind button on the Crossfire receiver within 20s of powering the RX.
-- Confirm the bind procedure on your TX.
+  * Confirm the bind procedure on your TX.
 {{:public:tbs-crossfire-diversity-nano-rx-full-range-receiver.jpg?400|}}
@@ Line 49: / Line 51: @@
 ===== Binding your DJI Goggle =====
-- Power on your DJI Goggle.
+  * Power on your DJI Goggle.
-- Connect the battery to your BNF model. Only do this with props removed or a smokestopper.
+  * Connect the battery to your BNF model. Only do this with props removed or a smokestopper.
-- Wait until the green LED appears on the DJI VTX.
+  * Wait until the Red LED appears on the DJI O3 VTX.
-- Press the red button on your DJI Goggle twice. It should beep twice every second.
+  * Press the button on your DJI Goggle. It should beep twice every second.
-- Press the button on the DJI VTX. The goggle confirms the binding by beeping twice.
+  * Press the button on the DJI VTX. The goggle confirms the binding by beeping twice.
 {{:public:dji-goggles-2.jpg?400|}}
@@ Line 60: / Line 62: @@
 ==== Change Flight Modes ====
-To reassign buttons on your remote controller, assign AUX channels to each flight mode using Betaflight.
+To reassign buttons on your remote controller, assign AUX channels to each flight mode using Inav configurator.
-- Connect the drone via USB port of the flight controller to your computer
+  * Connect the drone via USB port of the flight controller to your computer
-- launch INAV configurator
+  * launch INAV configurator
-- Connect to the correspondent port
+  * Connect to the correspondent port
-- Navigate to "Modes" tab
+  * Navigate to "Modes" tab
-- Choose AUTO for the mode in question and press the corresponding button on your TX
+  * Choose AUTO for the mode in question and press the corresponding button on your TX
-- Dont forget to hit save!
+  * Don't forget to hit save!
 {{:public:inav_modes.png}}
@@ Line 79: / Line 81: @@
 Rates affect the flight feel and determine the maximum speed of rotation around each axis for your drone. Our presets allow smooth and cinematic flight, but it is a good idea to experiment with the rates on order to find your personal settings.
-- Connect the drone via USB port of the flight controller to your computer
+  * Connect the drone via USB port of the flight controller to your computer
-- launch Betaflight configurator
+  * launch INAV configurator
-- Connect to the correspondent port
+  * Connect to the correspondent port
-- Navigate to "PID" tab
+  * Navigate to "PID" tab
-- Swap to "Rateprofile settings" tab
+  * Swap to "Rates & Expo" tab
-- Adapt the parameters to your needs
+  * Adapt the parameters to your needs
-- Dont forget to hit save!
+  * Don't forget to hit save!
-```
 This should keep the headings and formatting consistent with your specified style.