Differences

This shows you the differences between two versions of the page.

--- public:naked-action-6-manual [2026/05/04 12:26] – [Step - Connect Ribbon Cable to BEC] admin
+++ public:naked-action-6-manual [2026/05/04 12:43] (current) – [Step - Attach Lens] admin
@@ Line 15: / Line 15: @@
   * 1x Front Case
   * 1x Back Case
+  * 1x 3D Printed Lens Bracket Adapter
+  * 1x 3D Printed Lens Bracket Mount
   * 1x Alu ND Filter Mount
   * 1x Alu Mounting Bracket
   * 1x 3D Printed Slide-in TPU Mount
-  * 1x M1.6x6mm screw
+  * 2x M1.4x3mm screw
+  * 2x M1.4x8mm screw
   * 4x M1.6x8mm screw
   * 1x M1.6x12mm screw
@@ Line 24: / Line 27: @@
   * 2x M2*5mm screw
   * 3x M2x6mm screw
-  * 1x M1.6 nut
+  * 3x M2x3mm insert
-  * 3x M2x4mm insert
-  * 1x M2x3mm insert
   * 1x 3D Printed WiFi Mount
@@ Line 42: / Line 43: @@
   * Tweezers
   * HotAir Gun
+  * HotGlue Gun
   * Plastic Spudge
-  * UV flashlight
   * Kapton tape
   * Thin double sided tape
@@ Line 283: / Line 284: @@
 {{:public:naked_action_6_pro_v2_34_.jpg?nolink&800|}}
   * Use a cutter knife to remove some of the material that was used in the V1 version to make space for the lens bracket.
+==== Step - Lens Bracket Preparation ====
+{{:public:naked_action_6_pro_v2_9_.jpg?nolink&800|}}
+{{:public:naked_action_6_pro_v2_10_.jpg?nolink&800|}}
+  * Clean off all thermal paste from backside of the lens bracket
+{{:public:naked_action_6_pro_v2_35_.jpg?nolink&800|}}
+  * Remove this part from the bracket. You can use some side cutters to start and then use a file to file it down flush.
+{{:public:naked_action_6_pro_v2_15_.jpg?nolink&800|}}
+{{:public:naked_action_6_pro_v2_16_.jpg?nolink&800|}}
+  * The bracket should now look like this.
+  * Make sure to remove any metallic dust from it.
 ===== Assembly Steps =====
@@ Line 328: / Line 340: @@
 {{:public:naked_action_6_pro_v2_13_.jpg?nolink&800|}}
   * Connect the lens ribbon connector onto the motherboard.
+{{:public:naked_action_6_pro_v2_36_.jpg?nolink&800|}}
 {{:public:naked_action_6_pro_v2_17_.jpg?nolink&800|}}
 {{:public:naked_action_6_pro_v2_18_.jpg?nolink&800|}}
@@ Line 384: / Line 397: @@
 ===== Step - Close the Case =====
-{{:public:naked_action_6_assemble__33_.jpg?nolink&800|}}
+{{:public:naked_action_6_pro_v2_30_.jpg?nolink&800|}}
-{{:public:naked_action_6_assemble__34_.jpg?nolink&800|}}
+{{:public:naked_action_6_pro_v2_31_.jpg?nolink&800|}}
-{{:public:naked_action_6_assemble__35_.jpg?nolink&800|}}
-  * Add the six screws to the backcover.
+  * Place the BEC into the cutout for the BEC on the backcover.
-  * Align the BEC with the cutout for the BEC on the backcover.
+  * Add the six screws to the backcover. M1.6x8mm for the middle and right, M1.6x12mm for bottom left and M1.6x16mm for top right corner.
   * Screw in the screws to the frontcover, make sure not to overtighten them.
-==== Step - Attach Fan ====
-{{:public:naked_action_6_assemble__36_.jpg?nolink&800|}}
-  * Attach the cooling fan to the back case with M2*5 screws using an M2 hex tool.
-  * Make sure to get the fan direction right.
@@ Line 405: / Line 411: @@
 ===== Gyroflow Fix =====
+**With the V2 version that uses the original lens bracket this foam hack is not needed anymore**
 In its naked configuration, the DJI Action 6 camera may exhibit stabilization artifacts after processing footage with Gyroflow. These issues are caused by slight movement of the sensor PCB and its onboard gyro.