Differences

This shows you the differences between two versions of the page.

--- public:naked-action-6-manual [2026/05/04 12:24] – [Step - Fold Back Display Cable] admin
+++ public:naked-action-6-manual [2026/05/04 12:43] (current) – [Step - Attach Lens] admin
@@ Line 15: / Line 15: @@
   * 1x Front Case
   * 1x Back Case
+  * 1x 3D Printed Lens Bracket Adapter
+  * 1x 3D Printed Lens Bracket Mount
   * 1x Alu ND Filter Mount
   * 1x Alu Mounting Bracket
   * 1x 3D Printed Slide-in TPU Mount
-  * 1x M1.6x6mm screw
+  * 2x M1.4x3mm screw
+  * 2x M1.4x8mm screw
   * 4x M1.6x8mm screw
   * 1x M1.6x12mm screw
@@ Line 24: / Line 27: @@
   * 2x M2*5mm screw
   * 3x M2x6mm screw
-  * 1x M1.6 nut
+  * 3x M2x3mm insert
-  * 3x M2x4mm insert
-  * 1x M2x3mm insert
   * 1x 3D Printed WiFi Mount
@@ Line 42: / Line 43: @@
   * Tweezers
   * HotAir Gun
+  * HotGlue Gun
   * Plastic Spudge
-  * UV flashlight
   * Kapton tape
   * Thin double sided tape
@@ Line 283: / Line 284: @@
 {{:public:naked_action_6_pro_v2_34_.jpg?nolink&800|}}
   * Use a cutter knife to remove some of the material that was used in the V1 version to make space for the lens bracket.
+==== Step - Lens Bracket Preparation ====
+{{:public:naked_action_6_pro_v2_9_.jpg?nolink&800|}}
+{{:public:naked_action_6_pro_v2_10_.jpg?nolink&800|}}
+  * Clean off all thermal paste from backside of the lens bracket
+{{:public:naked_action_6_pro_v2_35_.jpg?nolink&800|}}
+  * Remove this part from the bracket. You can use some side cutters to start and then use a file to file it down flush.
+{{:public:naked_action_6_pro_v2_15_.jpg?nolink&800|}}
+{{:public:naked_action_6_pro_v2_16_.jpg?nolink&800|}}
+  * The bracket should now look like this.
+  * Make sure to remove any metallic dust from it.
 ===== Assembly Steps =====
@@ Line 328: / Line 340: @@
 {{:public:naked_action_6_pro_v2_13_.jpg?nolink&800|}}
   * Connect the lens ribbon connector onto the motherboard.
+{{:public:naked_action_6_pro_v2_36_.jpg?nolink&800|}}
 {{:public:naked_action_6_pro_v2_17_.jpg?nolink&800|}}
 {{:public:naked_action_6_pro_v2_18_.jpg?nolink&800|}}
@@ Line 378: / Line 391: @@
 ==== Step - Connect Ribbon Cable to BEC ====
 {{:public:naked_action_6_pro_v2_28_.jpg?nolink&800|}}
+{{:public:naked_action_6_pro_v2_29_.jpg?nolink&800|}}
-  * Solder the two cables to the BEC.
-==== Step - Attach BEC ====
-{{:public:naked_action_6_assemble__26_.jpg?nolink&800|}}
-{{:public:naked_action_6_assemble__27_.jpg?nolink&800|}}
-  * Place the BEC like shown.
   * Plug in the BEC ribbon cable like shown. You need to open the connector first by pulling softly on the two plastic locking pins. After you inserted the cable, lock them again by gently pushing them in at the same time. Make sure the cable stays straight.
-==== Step - Solder Camera Power to BEC ====
-{{:public:naked_action_6_assemble__28_.jpg?nolink&800|}}
-  * Solder the positive and negative cable from the mainboard to the correct pads on the BEC.
-==== Step - Solder Fan to BEC ====
-{{:public:naked_action_6_assemble__31_.jpg?nolink&800|}}
-{{:public:naked_action_6_assemble__32_.jpg?nolink&800|}}
-  * Solder the positive and negative fan cables to the correct pads on the BEC.
 ===== Step - Close the Case =====
-{{:public:naked_action_6_assemble__33_.jpg?nolink&800|}}
+{{:public:naked_action_6_pro_v2_30_.jpg?nolink&800|}}
-{{:public:naked_action_6_assemble__34_.jpg?nolink&800|}}
+{{:public:naked_action_6_pro_v2_31_.jpg?nolink&800|}}
-{{:public:naked_action_6_assemble__35_.jpg?nolink&800|}}
-  * Add the six screws to the backcover.
+  * Place the BEC into the cutout for the BEC on the backcover.
-  * Align the BEC with the cutout for the BEC on the backcover.
+  * Add the six screws to the backcover. M1.6x8mm for the middle and right, M1.6x12mm for bottom left and M1.6x16mm for top right corner.
   * Screw in the screws to the frontcover, make sure not to overtighten them.
-==== Step - Attach Fan ====
-{{:public:naked_action_6_assemble__36_.jpg?nolink&800|}}
-  * Attach the cooling fan to the back case with M2*5 screws using an M2 hex tool.
-  * Make sure to get the fan direction right.
@@ Line 422: / Line 411: @@
 ===== Gyroflow Fix =====
+**With the V2 version that uses the original lens bracket this foam hack is not needed anymore**
 In its naked configuration, the DJI Action 6 camera may exhibit stabilization artifacts after processing footage with Gyroflow. These issues are caused by slight movement of the sensor PCB and its onboard gyro.