Differences

This shows you the differences between two versions of the page.

--- public:naked-action-6-manual [2026/05/04 12:15] – [Step - Attach Lens] admin
+++ public:naked-action-6-manual [2026/05/04 12:43] (current) – [Step - Attach Lens] admin
@@ Line 15: / Line 15: @@
   * 1x Front Case
   * 1x Back Case
+  * 1x 3D Printed Lens Bracket Adapter
+  * 1x 3D Printed Lens Bracket Mount
   * 1x Alu ND Filter Mount
   * 1x Alu Mounting Bracket
   * 1x 3D Printed Slide-in TPU Mount
-  * 1x M1.6x6mm screw
+  * 2x M1.4x3mm screw
+  * 2x M1.4x8mm screw
   * 4x M1.6x8mm screw
   * 1x M1.6x12mm screw
@@ Line 24: / Line 27: @@
   * 2x M2*5mm screw
   * 3x M2x6mm screw
-  * 1x M1.6 nut
+  * 3x M2x3mm insert
-  * 3x M2x4mm insert
-  * 1x M2x3mm insert
   * 1x 3D Printed WiFi Mount
@@ Line 42: / Line 43: @@
   * Tweezers
   * HotAir Gun
+  * HotGlue Gun
   * Plastic Spudge
-  * UV flashlight
   * Kapton tape
   * Thin double sided tape
@@ Line 283: / Line 284: @@
 {{:public:naked_action_6_pro_v2_34_.jpg?nolink&800|}}
   * Use a cutter knife to remove some of the material that was used in the V1 version to make space for the lens bracket.
+==== Step - Lens Bracket Preparation ====
+{{:public:naked_action_6_pro_v2_9_.jpg?nolink&800|}}
+{{:public:naked_action_6_pro_v2_10_.jpg?nolink&800|}}
+  * Clean off all thermal paste from backside of the lens bracket
+{{:public:naked_action_6_pro_v2_35_.jpg?nolink&800|}}
+  * Remove this part from the bracket. You can use some side cutters to start and then use a file to file it down flush.
+{{:public:naked_action_6_pro_v2_15_.jpg?nolink&800|}}
+{{:public:naked_action_6_pro_v2_16_.jpg?nolink&800|}}
+  * The bracket should now look like this.
+  * Make sure to remove any metallic dust from it.
 ===== Assembly Steps =====
@@ Line 323: / Line 335: @@
 {{:public:naked_action_6_pro_v2_11_.jpg?nolink&800|}}
 {{:public:naked_action_6_pro_v2_12_.jpg?nolink&800|}}
-  * Place the 3d printed bracket on the left side of the lens mount.
+  * Place the lens assembly into its place.
+  * Then place the 3d printed bracket on the left side of the lens mount.
   * Secure with the 1x original screws and 2x M1.4x8mm screws.
 {{:public:naked_action_6_pro_v2_13_.jpg?nolink&800|}}
   * Connect the lens ribbon connector onto the motherboard.
+{{:public:naked_action_6_pro_v2_36_.jpg?nolink&800|}}
-  * Place the lens assembly into its place.
-  * Secure with the 3x original screws.
 {{:public:naked_action_6_pro_v2_17_.jpg?nolink&800|}}
+{{:public:naked_action_6_pro_v2_18_.jpg?nolink&800|}}
-  * Connect the lens ribbon connector and the front display ribbon connector onto the motherboard.
+  * Add the second 3d printed part where the lens ribbon bracket was sitting and secure it with the original screws.
+  * Then add the lens bracket to the lens and secure it with the three original screws.
-{{:public:naked_action_6_assemble__19_.jpg?nolink&800|}}
-{{:public:naked_action_6_assemble__20_.jpg?nolink&800|}}
-  * Secure the connector with the silver plate and two screws.
 ==== Step - Attach BEC Ribbon Cable ====
-{{:public:naked_action_6_assemble__21_.jpg?nolink&800|}}
+{{:public:naked_action_6_pro_v2_19_.jpg?nolink&800|}}
-{{:public:naked_action_6_assemble__22_.jpg?nolink&800|}}
-{{:public:naked_action_6_assemble__23_.jpg?nolink&800|}}
   * Attach the BEC ribbon cable like shown.
@@ Line 350: / Line 352: @@
 ==== Step - Attach Back Display Cable ====
-{{:public:naked_action_6_assemble__24_.jpg?nolink&800|}}
+{{:public:naked_action_6_pro_v2_20_.jpg?nolink&800|}}
-{{:public:naked_action_6_assemble__25_.jpg?nolink&800|}}
   * Attach the back display cable like shown.
   * Make sure to align the connector properly before applying pressure as a wrong alignment may damage the connector.
-  * Fold down the cable like shown.
-==== Step - Attach BEC ====
+==== Step - Secure Ribbon Cable Connectors ====
-{{:public:naked_action_6_assemble__26_.jpg?nolink&800|}}
+{{:public:naked_action_6_pro_v2_21_.jpg?nolink&800|}}
-{{:public:naked_action_6_assemble__27_.jpg?nolink&800|}}
+  * Use a little dab of hot glue to secure the connectors in place and protect them from popping off.
+==== Step - Fold Back Display Cable ====
+{{:public:naked_action_6_pro_v2_22_.jpg?nolink&800|}}
+  * Fold the back display cable like shown.
-  * Place the BEC like shown.
+==== Step - Prepare Fan ====
-  * Plug in the BEC ribbon cable like shown. You need to open the connector first by pulling softly on the two plastic locking pins. After you inserted the cable, lock them again by gently pushing them in at the same time. Make sure the cable stays straight.
+{{:public:naked_action_6_pro_v2_23_.jpg?nolink&800|}}
+  * Grab the back case.
+  * Feed the fan wires trough the fan opening.
+  * Secure the fan with 2x M2x5mm screws.
+  * Make sure to get the fan orientation right.
-==== Step - Solder Camera Power to BEC ====
+==== Step - Prepare BEC ====
-{{:public:naked_action_6_assemble__28_.jpg?nolink&800|}}
+{{:public:naked_action_6_pro_v2_24_.jpg?nolink&800|}}
-  * Solder the positive and negative cable from the mainboard to the correct pads on the BEC.
+{{:public:naked_action_6_pro_v2_25_.jpg?nolink&800|}}
-==== Step - Prepare Fan ====
+  * Add some foam double sided tape to the backside of the BEC
-{{:public:naked_action_6_assemble__29_.jpg?nolink&800|}}
-{{:public:naked_action_6_assemble__30_.jpg?nolink&800|}}
-  * Feed the fan wires trough the fan opening.
+==== Step - Prepare Cables ====
+{{:public:naked_action_6_pro_v2_26_.jpg?nolink&800|}}
-==== Step - Solder Fan to BEC ====
+  * Solder the fan cables and the mainboard power cables together.
-{{:public:naked_action_6_assemble__31_.jpg?nolink&800|}}
-{{:public:naked_action_6_assemble__32_.jpg?nolink&800|}}
+==== Step - Solder BEC ====
+{{:public:naked_action_6_pro_v2_27_.jpg?nolink&800|}}
+  * Solder the two cables to the BEC.
+  * Make sure to get the polarity right.
+==== Step - Connect Ribbon Cable to BEC ====
+{{:public:naked_action_6_pro_v2_28_.jpg?nolink&800|}}
+{{:public:naked_action_6_pro_v2_29_.jpg?nolink&800|}}
+  * Plug in the BEC ribbon cable like shown. You need to open the connector first by pulling softly on the two plastic locking pins. After you inserted the cable, lock them again by gently pushing them in at the same time. Make sure the cable stays straight.
-  * Solder the positive and negative fan cables to the correct pads on the BEC.
 ===== Step - Close the Case =====
-{{:public:naked_action_6_assemble__33_.jpg?nolink&800|}}
+{{:public:naked_action_6_pro_v2_30_.jpg?nolink&800|}}
-{{:public:naked_action_6_assemble__34_.jpg?nolink&800|}}
+{{:public:naked_action_6_pro_v2_31_.jpg?nolink&800|}}
-{{:public:naked_action_6_assemble__35_.jpg?nolink&800|}}
-  * Add the six screws to the backcover.
+  * Place the BEC into the cutout for the BEC on the backcover.
-  * Align the BEC with the cutout for the BEC on the backcover.
+  * Add the six screws to the backcover. M1.6x8mm for the middle and right, M1.6x12mm for bottom left and M1.6x16mm for top right corner.
   * Screw in the screws to the frontcover, make sure not to overtighten them.
-==== Step - Attach Fan ====
-{{:public:naked_action_6_assemble__36_.jpg?nolink&800|}}
-  * Attach the cooling fan to the back case with M2*5 screws using an M2 hex tool.
-  * Make sure to get the fan direction right.
@@ Line 403: / Line 411: @@
 ===== Gyroflow Fix =====
+**With the V2 version that uses the original lens bracket this foam hack is not needed anymore**
 In its naked configuration, the DJI Action 6 camera may exhibit stabilization artifacts after processing footage with Gyroflow. These issues are caused by slight movement of the sensor PCB and its onboard gyro.