Differences

This shows you the differences between two versions of the page.

--- public:naked-action-6-manual [2026/02/02 13:50] – [Step - Assemble Main Components] admin
+++ public:naked-action-6-manual [2026/02/09 10:55] (current) – laurin
@@ Line 1: / Line 1: @@
 ====== Naked Action 6 DIY Manual ======
-{{:public:action_6.jpg?nolink&600|}}
+{{:public:naked_action_6_pro_1_.jpg?nolink&600|}}
 ===== General Information =====
@@ Line 264: / Line 264: @@
 {{:public:action_6__54_.jpg?nolink&800|}}
   * Cut the ribbon PCB like shown in the picture.
 ===== Assembly Steps =====
+==== Step - Install Nuts ====
+{{:public:naked_action_6_assemble__39_.jpg?nolink&800|}}
+{{:public:naked_action_6_assemble__41_.jpg?nolink&800|}}
+{{:public:naked_action_6_assemble__42_.jpg?nolink&800|}}
+  * Use a soldering iron set to 220 degrees to slowly set in the nuts into the frontcover.
+  * Make sure to set them straight.
+  * Do not rotate the nuts.
 ==== Step - Install Front Display ====
@@ Line 277: / Line 286: @@
   * Wait for the epoxy to cure.
-==== Step - Install Nuts ====
-{{:public:naked_action_6_assemble__39_.jpg?nolink&800|}}
-{{:public:naked_action_6_assemble__41_.jpg?nolink&800|}}
-{{:public:naked_action_6_assemble__42_.jpg?nolink&800|}}
-  * Use a soldering iron set to 220 degrees to slowly set in the nuts into the frontcover.
-  * Make sure to set them straight.
-  * Do not rotate the nuts.
 ==== Step - Attach 3d Printed Bracket ====
@@ Line 293: / Line 294: @@
 {{:public:naked_action_6_assemble__8_.jpg?nolink&800|}}
-  * Add the 3d printed bracket like shown and secure with two screws
+  * Add the 3d printed bracket like shown and secure with two M1.4 x 3mm screws
 ==== Step - Attach Motherboard ====
@@ Line 350: / Line 351: @@
 ==== Step - Solder Camera Power to BEC ====
-{{:public:nake_action_6_assemble__28_.jpg?nolink&800|}}
+{{:public:naked_action_6_assemble__28_.jpg?nolink&800|}}
   * Solder the positive and negative cable from the mainboard to the correct pads on the BEC.
@@ Line 365: / Line 366: @@
   * Solder the positive and negative fan cables to the correct pads on the BEC.
-==== Step - Close the Case ====
+===== Step - Close the Case =====
 {{:public:naked_action_6_assemble__33_.jpg?nolink&800|}}
 {{:public:naked_action_6_assemble__34_.jpg?nolink&800|}}
@@ Line 383: / Line 384: @@
 ==== Step - Final Camera ====
-{{:public:naked_action_6_assembly__37_.jpg?nolink&800|}}
+{{:public:naked_action_6_pro_1_.jpg?nolink&800|}}
   * Add a ND Filter to protect the camera lens
+===== Gyroflow Fix =====
+In its naked configuration, the DJI Action 6 camera may exhibit stabilization artifacts after processing footage with Gyroflow. These issues are caused by slight movement of the sensor PCB and its onboard gyro.
+To resolve this, place a piece of foam between the rear cover and the sensor PCB. The foam must apply firm pressure to securely fix the sensor assembly. Correct pressure is achieved when the rear cover needs to be pressed onto the camera by hand before inserting the screws.
+When installed correctly, this fix prevents micro-movement of the sensor and results in smooth, reliable video output, significantly improving stabilization performance when using Gyroflow or RockSteady.
+Our recommendation for Gyroflow settings are:
+  * Low pass filter: 50hz
+  * Disable rolling shutter correction
+{{:public:action_6_foam_1.jpeg?nolink&800|}}
+{{:public:action_6_foam_5.jpeg?nolink&800|}}
+{{:public:action_6_foam_6.jpeg?nolink&800|}}
+{{:public:action_6_foam_2.jpeg?nolink&800|}}
+{{:public:action_6_foam_4.jpeg?nolink&800|}}
+===== BEC Power Pinout =====
 {{:public:A5_bec_pinout.jpeg?nolink&800|}}