Differences

This shows you the differences between two versions of the page.

--- public:naked-action-6-manual [2026/02/02 13:48] – [Step - Install Front Display] admin
+++ public:naked-action-6-manual [2026/03/16 16:08] (current) – admin
@@ Line 1: / Line 1: @@
+{{htmlmetatags>metatag-og:image=(https://wiki.fpvframe.ch/_media/public:icon_fpvframe.png)}}
 ====== Naked Action 6 DIY Manual ======
-{{:public:action_6.jpg?nolink&600|}}
+{{:public:naked_action_6_pro_1_.jpg?nolink&600|}}
 ===== General Information =====
@@ Line 228: / Line 230: @@
 ==== Step - Mainboard Preparation ====
-** There are some very small components next to where you will need to solder. Be careful to not damage or desolder any of the mainboard components during the following steps. **
+** There are some very small components next to where you will need to solder. Be careful to not damage or desolder any of the mainboard components during the following steps. If you are not comfortable doing this you can skip to the next step and do the alternative version**
 {{:public:action_5_disassemble_60_.jpg?nolink&800|}}
@@ Line 243: / Line 245: @@
+==== Step - Mainboard Preparation Alternative Version ====
+If you did the step above skip this. If you are not comfortable doing the step above you can do the preparation like shown below. It will add a bit of weight to the build.
+{{:public:naked_action_6_pro_connector_1.jpg
+?nolink&800|}}
+{{:public:naked_action_6_pro_connector_2.jpg
+?nolink&800|}}
+Solder the powercables directly to the battery connector of the mainboard.
 ==== Step - Back Display Preperation ====
@@ Line 264: / Line 277: @@
 {{:public:action_6__54_.jpg?nolink&800|}}
   * Cut the ribbon PCB like shown in the picture.
 ===== Assembly Steps =====
+==== Step - Install Nuts ====
+{{:public:naked_action_6_assemble__39_.jpg?nolink&800|}}
+{{:public:naked_action_6_assemble__41_.jpg?nolink&800|}}
+{{:public:naked_action_6_assemble__42_.jpg?nolink&800|}}
+  * Use a soldering iron set to 220 degrees to slowly set in the nuts into the frontcover.
+  * Make sure to set them straight.
+  * Do not rotate the nuts.
 ==== Step - Install Front Display ====
@@ Line 277: / Line 299: @@
   * Wait for the epoxy to cure.
-==== Step - Install Nuts ====
-{{:public:naked_action_6_assemble__39_.jpg?nolink&800|}}
-{{:public:naked_action_6_assemble__41_.jpg?nolink&800|}}
-{{:public:naked_action_6_assemble__42_.jpg?nolink&800|}}
-  * Use a soldering iron set to 220 degrees to slowly set in the nuts into the frontcover.
-  * Make sure to set them straight.
-  * Do not rotate the nuts.
 ==== Step - Attach 3d Printed Bracket ====
@@ Line 293: / Line 307: @@
 {{:public:naked_action_6_assemble__8_.jpg?nolink&800|}}
-  * Add the 3d printed bracket like shown and secure with two screws
+  * Add the 3d printed bracket like shown and secure with two M1.4 x 3mm screws
 ==== Step - Attach Motherboard ====
@@ Line 350: / Line 364: @@
 ==== Step - Solder Camera Power to BEC ====
-{{:public:nake_action_6_assemble__28_.jpg?nolink&800|}}
+{{:public:naked_action_6_assemble__28_.jpg?nolink&800|}}
   * Solder the positive and negative cable from the mainboard to the correct pads on the BEC.
@@ Line 365: / Line 379: @@
   * Solder the positive and negative fan cables to the correct pads on the BEC.
-==== Step - Close the Case ====
+===== Step - Close the Case =====
 {{:public:naked_action_6_assemble__33_.jpg?nolink&800|}}
 {{:public:naked_action_6_assemble__34_.jpg?nolink&800|}}
@@ Line 382: / Line 396: @@
-==== Step - Assemble Main Components ====
+==== Step - Final Camera ====
-{{:public:action_6__56_.jpg?nolink&800|}}
+{{:public:naked_action_6_pro_1_.jpg?nolink&800|}}
+  * Add a ND Filter to protect the camera lens
+===== Gyroflow Fix =====
+In its naked configuration, the DJI Action 6 camera may exhibit stabilization artifacts after processing footage with Gyroflow. These issues are caused by slight movement of the sensor PCB and its onboard gyro.
+To resolve this, place a piece of foam between the rear cover and the sensor PCB. The foam must apply firm pressure to securely fix the sensor assembly. Correct pressure is achieved when the rear cover needs to be pressed onto the camera by hand before inserting the screws.
+When installed correctly, this fix prevents micro-movement of the sensor and results in smooth, reliable video output, significantly improving stabilization performance when using Gyroflow or RockSteady.
+Our recommendation for Gyroflow settings are:
+  * Low pass filter: 50hz
+  * Disable rolling shutter correction
-{{:public:action_6__57_.jpg?nolink&800|}}
-{{:public:action_6__58_.jpg?nolink&800|}}
+{{:public:action_6_foam_1.jpeg?nolink&800|}}
+{{:public:action_6_foam_5.jpeg?nolink&800|}}
+{{:public:action_6_foam_6.jpeg?nolink&800|}}
+{{:public:action_6_foam_2.jpeg?nolink&800|}}
+{{:public:action_6_foam_4.jpeg?nolink&800|}}
-Final assembly
-  * Place the BEC into the back case and screw the front and back cases together using 4x M1.6*8, 1x M1.6*12, and 1x M1.6*16 screws with a PH0 screwdriver. The longest 16mm screw goes in the top left corner, the 12mm screw in the bottom left, and the 8mm screws in the remaining holes.
+===== BEC Power Pinout =====
 {{:public:A5_bec_pinout.jpeg?nolink&800|}}