Differences

This shows you the differences between two versions of the page.

--- public:naked-action-6-manual [2026/02/02 13:46] – [Step - Attach Fan] admin
+++ public:naked-action-6-manual [2026/02/09 10:55] (current) – laurin
@@ Line 1: / Line 1: @@
 ====== Naked Action 6 DIY Manual ======
-{{:public:action_6.jpg?nolink&600|}}
+{{:public:naked_action_6_pro_1_.jpg?nolink&600|}}
 ===== General Information =====
@@ Line 264: / Line 264: @@
 {{:public:action_6__54_.jpg?nolink&800|}}
   * Cut the ribbon PCB like shown in the picture.
 ===== Assembly Steps =====
+==== Step - Install Nuts ====
+{{:public:naked_action_6_assemble__39_.jpg?nolink&800|}}
+{{:public:naked_action_6_assemble__41_.jpg?nolink&800|}}
+{{:public:naked_action_6_assemble__42_.jpg?nolink&800|}}
+  * Use a soldering iron set to 220 degrees to slowly set in the nuts into the frontcover.
+  * Make sure to set them straight.
+  * Do not rotate the nuts.
 ==== Step - Install Front Display ====
@@ Line 285: / Line 294: @@
 {{:public:naked_action_6_assemble__8_.jpg?nolink&800|}}
-  * Add the 3d printed bracket like shown and secure with two screws
+  * Add the 3d printed bracket like shown and secure with two M1.4 x 3mm screws
 ==== Step - Attach Motherboard ====
@@ Line 318: / Line 327: @@
 ==== Step - Attach BEC Ribbon Cable ====
-{{:public:nake_action_6_assemble__21_.jpg?nolink&800|}}
+{{:public:naked_action_6_assemble__21_.jpg?nolink&800|}}
-{{:public:nake_action_6_assemble__22_.jpg?nolink&800|}}
+{{:public:naked_action_6_assemble__22_.jpg?nolink&800|}}
-{{:public:nake_action_6_assemble__23_.jpg?nolink&800|}}
+{{:public:naked_action_6_assemble__23_.jpg?nolink&800|}}
   * Attach the BEC ribbon cable like shown.
@@ Line 326: / Line 335: @@
 ==== Step - Attach Back Display Cable ====
-{{:public:nake_action_6_assemble__24_.jpg?nolink&800|}}
+{{:public:naked_action_6_assemble__24_.jpg?nolink&800|}}
-{{:public:nake_action_6_assemble__25_.jpg?nolink&800|}}
+{{:public:naked_action_6_assemble__25_.jpg?nolink&800|}}
   * Attach the back display cable like shown.
   * Make sure to align the connector properly before applying pressure as a wrong alignment may damage the connector.
@@ Line 333: / Line 342: @@
 ==== Step - Attach BEC ====
-{{:public:nake_action_6_assemble__26_.jpg?nolink&800|}}
+{{:public:naked_action_6_assemble__26_.jpg?nolink&800|}}
-{{:public:nake_action_6_assemble__27_.jpg?nolink&800|}}
+{{:public:naked_action_6_assemble__27_.jpg?nolink&800|}}
@@ Line 342: / Line 351: @@
 ==== Step - Solder Camera Power to BEC ====
-{{:public:nake_action_6_assemble__28_.jpg?nolink&800|}}
+{{:public:naked_action_6_assemble__28_.jpg?nolink&800|}}
   * Solder the positive and negative cable from the mainboard to the correct pads on the BEC.
 ==== Step - Prepare Fan ====
-{{:public:nake_action_6_assemble__29_.jpg?nolink&800|}}
+{{:public:naked_action_6_assemble__29_.jpg?nolink&800|}}
-{{:public:nake_action_6_assemble__30_.jpg?nolink&800|}}
+{{:public:naked_action_6_assemble__30_.jpg?nolink&800|}}
   * Feed the fan wires trough the fan opening.
 ==== Step - Solder Fan to BEC ====
-{{:public:nake_action_6_assemble__31_.jpg?nolink&800|}}
+{{:public:naked_action_6_assemble__31_.jpg?nolink&800|}}
-{{:public:nake_action_6_assemble__32_.jpg?nolink&800|}}
+{{:public:naked_action_6_assemble__32_.jpg?nolink&800|}}
   * Solder the positive and negative fan cables to the correct pads on the BEC.
-==== Step - Close the Case ====
+===== Step - Close the Case =====
-{{:public:nake_action_6_assemble__33_.jpg?nolink&800|}}
+{{:public:naked_action_6_assemble__33_.jpg?nolink&800|}}
-{{:public:nake_action_6_assemble__34_.jpg?nolink&800|}}
+{{:public:naked_action_6_assemble__34_.jpg?nolink&800|}}
-{{:public:nake_action_6_assemble__35_.jpg?nolink&800|}}
+{{:public:naked_action_6_assemble__35_.jpg?nolink&800|}}
   * Add the six screws to the backcover.
@@ Line 368: / Line 377: @@
 ==== Step - Attach Fan ====
-{{:public:nake_action_6_assemble__36_.jpg?nolink&800|}}
+{{:public:naked_action_6_assemble__36_.jpg?nolink&800|}}
   * Attach the cooling fan to the back case with M2*5 screws using an M2 hex tool.
@@ Line 374: / Line 383: @@
-==== Step - Assemble Main Components ====
+==== Step - Final Camera ====
-{{:public:action_6__56_.jpg?nolink&800|}}
+{{:public:naked_action_6_pro_1_.jpg?nolink&800|}}
+  * Add a ND Filter to protect the camera lens
+===== Gyroflow Fix =====
+In its naked configuration, the DJI Action 6 camera may exhibit stabilization artifacts after processing footage with Gyroflow. These issues are caused by slight movement of the sensor PCB and its onboard gyro.
+To resolve this, place a piece of foam between the rear cover and the sensor PCB. The foam must apply firm pressure to securely fix the sensor assembly. Correct pressure is achieved when the rear cover needs to be pressed onto the camera by hand before inserting the screws.
+When installed correctly, this fix prevents micro-movement of the sensor and results in smooth, reliable video output, significantly improving stabilization performance when using Gyroflow or RockSteady.
+Our recommendation for Gyroflow settings are:
+  * Low pass filter: 50hz
+  * Disable rolling shutter correction
-{{:public:action_6__57_.jpg?nolink&800|}}
-{{:public:action_6__58_.jpg?nolink&800|}}
+{{:public:action_6_foam_1.jpeg?nolink&800|}}
+{{:public:action_6_foam_5.jpeg?nolink&800|}}
+{{:public:action_6_foam_6.jpeg?nolink&800|}}
+{{:public:action_6_foam_2.jpeg?nolink&800|}}
+{{:public:action_6_foam_4.jpeg?nolink&800|}}
-Final assembly
-  * Place the BEC into the back case and screw the front and back cases together using 4x M1.6*8, 1x M1.6*12, and 1x M1.6*16 screws with a PH0 screwdriver. The longest 16mm screw goes in the top left corner, the 12mm screw in the bottom left, and the 8mm screws in the remaining holes.
+===== BEC Power Pinout =====
 {{:public:A5_bec_pinout.jpeg?nolink&800|}}