Differences

This shows you the differences between two versions of the page.

--- public:naked-action-6-manual [2025/12/22 09:54] – [Step - Attach Motherboard] admin
+++ public:naked-action-6-manual [2025/12/22 12:17] (current) – admin
@@ Line 1: / Line 1: @@
-====== Naked Action 5 DIY Manual ======
+====== Naked Action 6 DIY Manual ======
 {{:public:action_6.jpg?nolink&600|}}
@@ Line 314: / Line 314: @@
 ==== Step - Assemble Main Components ====
-{{:public:action_5_assemble_6_.jpg?nolink&800|}}
+{{:public:action_6__56_.jpg?nolink&800|}}
-{{:public:action_5_assemble_7_.jpg?nolink&800|}}
-  * Place the motherboard holder into the naked action 5 front case and secure it with the four silver screws.
-  * Screw an M1.6*6 screw through the top right hole and secure it with an M1.6 nut inside for additional strength.
-{{:public:action_5_assemble_8_.jpg?nolink&800|}}
-  * Attach an ND filter to protect the lens during installation.
-{{:public:action_5_assemble_9_.jpg?nolink&800|}}
-  * Install the mainboard with the two screws.
-{{:public:action_5_assemble_10_.jpg?nolink&800|}}
-  * Install the lens and secure it with three lens screws.
-{{:public:action_5_assemble_11_.jpg?nolink&800|}}
-  * Plug in the lens ribbon cable to the mainboard. Ensure correct alignment before applying force.
-{{:public:action_5_assemble_12_.jpg?nolink&800|}}
-  * Add the silver lens ribbon bracket and secure it with two screws.
-{{:public:action_5_assemble_13_.jpg?nolink&800|}}
-  * Attach the WiFi module holder and secure it with a screw. Use a spare long M1.6 screw from the disassembly.
-{{:public:action_5_assemble_16_.jpg?nolink&800|}}
-  * Add the WiFi module on top of it and secure it with a spare short M1.6 screw from the disassembly.
-{{:public:action_5_assemble_17_.jpg?nolink&800|}}
-  * Add the WiFi module antenna cables and connect them on both sides.
-{{:public:action_5_assemble_18_.jpg?nolink&800|}}
-  * Fold the sensor and button ribbon cable to a package, secure it with tape.
-{{:public:action_5_assemble_19_.jpg?nolink&800|}}
-{{:public:action_5_assemble_20_.jpg?nolink&800|}}
-  * Add the WiFi ribbon cable and connect it on both sides. Ensure correct alignment before applying force.
-  * Make sure the ribbon cable package is placed under the WiFi ribbon cable.
-{{:public:action_5_assemble_22_.jpg?nolink&800|}}
-  * Plug in the front display ribbon cable to the mainboard. Ensure correct alignment before applying force.
-{{:public:action_5_assemble__38_.jpg?nolink&800|}}
-{{:public:action_5_assemble__37_.jpg?nolink&800|}}
-  * Add the back display cable and tape it together to a compact package sitting ontop of the mainboard.
-{{:public:action_5_assemble_25_.jpg?nolink&800|}}
-{{:public:action_5_assemble_26_.jpg?nolink&800|}}
-  * Attach the cooling fan to the back case with M2*5 screws using an M2 hex tool.
-  * Make sure to get the fan direction right.
-{{:public:action_5_assemble__39_.jpg?nolink&800|}}
-{{:public:action_5_assemble__40_.jpg?nolink&800|}}
-{{:public:action_5_assemble__41_.jpg?nolink&800|}}
-  * Shorten the fan power cables.
-  * Shorten the mainboard power cables.
-  * Shorten the button cable.
-  * Pretinn the 5v, GND and PWR pads.
-  * Solder both red cables to the 5v pad.
-  * Solder both black cables to the GND pad.
-  * Solder the white button cable to the PWR pad.
-{{:public:action_5_assemble__42_.jpg?nolink&800|}}
-  * Plug in the BEC ribbon cable to the mainboard. Ensure correct alignment before applying force.
-{{:public:action_5_assemble__44_.jpg?nolink&800|}}
-  * Connect BEC ribbon cable to the BEC. Ensure correct alignment before applying force.
-  * You will need to open the black bracket, slide in the ribbon cable and then close the bracket again.
-{{:public:action_5_assemble_33_.jpg?nolink&800|}}
-  * Power up the camera using a smoke stopper and the correct voltage to test your camera.
+{{:public:action_6__57_.jpg?nolink&800|}}
+{{:public:action_6__58_.jpg?nolink&800|}}
 Final assembly