Differences

This shows you the differences between two versions of the page.

--- public:naked-action-6-manual [2025/12/22 09:44] – [Step - Install Thread Inserts] admin
+++ public:naked-action-6-manual [2025/12/22 12:17] (current) – admin
@@ Line 1: / Line 1: @@
-====== Naked Action 5 DIY Manual ======
+====== Naked Action 6 DIY Manual ======
 {{:public:action_6.jpg?nolink&600|}}
@@ Line 268: / Line 268: @@
 ==== Step - Install Front Display ====
-{{:public:dji_a4_naked_manual-42.jpg?nolink&800|}}
+{{:public:action_6__39_.jpg?nolink&800|}}
-{{:public:action_5_assemble_2_.jpg?nolink&800|}}
-{{:public:action_5_assemble_3_.jpg?nolink&800|}}
   * Scruff up the surface of the Frontcover a little bit for better adhesion.
@@ Line 277: / Line 275: @@
   * Wait for the epoxy to cure.
-==== Step - Attach Sensor and Button Ribbon Cable ====
-{{:public:action_5_assemble_4_.jpg?nolink&800|}}
-  * Put the Sensors to the cutout on the front side of the case using the double sided tape thats already on the sensor.
-  * If the original double sided tape doesn't stick anymore replace it with some new thin double sided tape.
 ==== Step - Attach ND Filter Adapter ====
-{{:public:action_5_assemble_5_.jpg?nolink&800|}}
+{{:public:action_6__40_.jpg?nolink&800|}}
-  * Screw the aluminum ND filter adapter to the motherboard holder.
+  * Place the motherboard holder into the case, screw on the clear filter from the front.
+  * Secure the motherboard holder with screws.
+==== Step - Attach Lens ====
+{{:public:action_6__42_.jpg?nolink&800|}}
+  * Place the lens assembly into its place.
+  * Secure with the 3x original screws.
+==== Step - Attach Motherboard ====
+{{:public:action_6__43_.jpg?nolink&800|}}
+  * Place the motherboard ontop of the motherboard holder and secure with two screws.
+{{:public:action_6__44_.jpg?nolink&800|}}
+  * Connect the lens ribbon connector and the front display ribbon connector onto the motherboard.
+{{:public:action_6__45_.jpg?nolink&800|}}
+  * Secure the connector with the silver plate and two screws.
+==== Step - Attach Fan ====
+{{:public:action_6__55_.jpg?nolink&800|}}
-==== Step - Assemble Main Components ====
-{{:public:action_5_assemble_6_.jpg?nolink&800|}}
-{{:public:action_5_assemble_7_.jpg?nolink&800|}}
-  * Place the motherboard holder into the naked action 5 front case and secure it with the four silver screws.
-  * Screw an M1.6*6 screw through the top right hole and secure it with an M1.6 nut inside for additional strength.
-{{:public:action_5_assemble_8_.jpg?nolink&800|}}
-  * Attach an ND filter to protect the lens during installation.
-{{:public:action_5_assemble_9_.jpg?nolink&800|}}
-  * Install the mainboard with the two screws.
-{{:public:action_5_assemble_10_.jpg?nolink&800|}}
-  * Install the lens and secure it with three lens screws.
-{{:public:action_5_assemble_11_.jpg?nolink&800|}}
-  * Plug in the lens ribbon cable to the mainboard. Ensure correct alignment before applying force.
-{{:public:action_5_assemble_12_.jpg?nolink&800|}}
-  * Add the silver lens ribbon bracket and secure it with two screws.
-{{:public:action_5_assemble_13_.jpg?nolink&800|}}
-  * Attach the WiFi module holder and secure it with a screw. Use a spare long M1.6 screw from the disassembly.
-{{:public:action_5_assemble_16_.jpg?nolink&800|}}
-  * Add the WiFi module on top of it and secure it with a spare short M1.6 screw from the disassembly.
-{{:public:action_5_assemble_17_.jpg?nolink&800|}}
-  * Add the WiFi module antenna cables and connect them on both sides.
-{{:public:action_5_assemble_18_.jpg?nolink&800|}}
-  * Fold the sensor and button ribbon cable to a package, secure it with tape.
-{{:public:action_5_assemble_19_.jpg?nolink&800|}}
-{{:public:action_5_assemble_20_.jpg?nolink&800|}}
-  * Add the WiFi ribbon cable and connect it on both sides. Ensure correct alignment before applying force.
-  * Make sure the ribbon cable package is placed under the WiFi ribbon cable.
-{{:public:action_5_assemble_22_.jpg?nolink&800|}}
-  * Plug in the front display ribbon cable to the mainboard. Ensure correct alignment before applying force.
-{{:public:action_5_assemble__38_.jpg?nolink&800|}}
-{{:public:action_5_assemble__37_.jpg?nolink&800|}}
-  * Add the back display cable and tape it together to a compact package sitting ontop of the mainboard.
-{{:public:action_5_assemble_25_.jpg?nolink&800|}}
-{{:public:action_5_assemble_26_.jpg?nolink&800|}}
   * Attach the cooling fan to the back case with M2*5 screws using an M2 hex tool.
   * Make sure to get the fan direction right.
-{{:public:action_5_assemble__39_.jpg?nolink&800|}}
-{{:public:action_5_assemble__40_.jpg?nolink&800|}}
-{{:public:action_5_assemble__41_.jpg?nolink&800|}}
-  * Shorten the fan power cables.
-  * Shorten the mainboard power cables.
-  * Shorten the button cable.
-  * Pretinn the 5v, GND and PWR pads.
-  * Solder both red cables to the 5v pad.
-  * Solder both black cables to the GND pad.
-  * Solder the white button cable to the PWR pad.
-{{:public:action_5_assemble__42_.jpg?nolink&800|}}
-  * Plug in the BEC ribbon cable to the mainboard. Ensure correct alignment before applying force.
-{{:public:action_5_assemble__44_.jpg?nolink&800|}}
-  * Connect BEC ribbon cable to the BEC. Ensure correct alignment before applying force.
-  * You will need to open the black bracket, slide in the ribbon cable and then close the bracket again.
-{{:public:action_5_assemble_33_.jpg?nolink&800|}}
-  * Power up the camera using a smoke stopper and the correct voltage to test your camera.
+==== Step - Assemble Main Components ====
+{{:public:action_6__56_.jpg?nolink&800|}}
+{{:public:action_6__57_.jpg?nolink&800|}}
+{{:public:action_6__58_.jpg?nolink&800|}}
 Final assembly