Differences

This shows you the differences between two versions of the page.

--- public:naked-action-6-manual [2025/12/22 09:25] – [Step - Mainboard Preparation] admin
+++ public:naked-action-6-manual [2025/12/22 12:17] (current) – admin
@@ Line 1: / Line 1: @@
-====== Naked Action 5 DIY Manual ======
+====== Naked Action 6 DIY Manual ======
 {{:public:action_6.jpg?nolink&600|}}
@@ Line 227: / Line 227: @@
 ==== Step - Mainboard Preparation ====
+** There are some very small components next to where you will need to solder. Be careful to not damage or desolder any of the mainboard components during the following steps. **
 {{:public:action_5_disassemble_60_.jpg?nolink&800|}}
   * Clean up all leftover glue next to the ribbon connectors, use heat and some plastic tweezers for this making sure to not damage any components on the mainboard.
@@ Line 242: / Line 245: @@
 ==== Step - Back Display Preperation ====
-{{:public:action_5_disassemble_72_.jpg?nolink&800|}}
+{{:public:action_6__46_.jpg?nolink&800|}}
   * Now we remove the needed parts from the back display.
-  * Clean up all the thermal paste leftover on the back display.
+{{:public:action_6__47_.jpg?nolink&800|}}
-{{:public:action_5_disassemble_73_.jpg?nolink&800|}}
+  * Start by cutting a groove at the bottom left corner next to the ribbon cable.
-  * Start by cutting a groove at the bottom right corner.
+{{:public:action_6__48_.jpg?nolink&800|}}
-{{:public:action_5_disassemble_74_.jpg?nolink&800|}}
+  * Pry open the shielding from the display and remove it with some pliers.
-  * Pry open the shielding from the display and remove it.
+{{:public:action_6__49_.jpg?nolink&800|}}
-{{:public:action_5_disassemble_75_.jpg?nolink&800|}}
+  * The backdisplay should now look like this.
-  * Do this piece for piece with some pliers.
+{{:public:action_6__50_.jpg?nolink&800|}}
-{{:public:action_5_disassemble_76_.jpg?nolink&800|}}
+  * Remove the stickers ontop of the pcb. Adding some heat will help. Make sure to not damage the pcb.
-  * Once you have a whole section removed it gets easier.
+{{:public:action_6__51_.jpg?nolink&800|}}
-{{:public:action_5_disassemble_77_.jpg?nolink&800|}}
-  * Now you can see the ribbon PCB on the back of the back display.
-{{:public:action_5_disassemble_78_.jpg?nolink&800|}}
-  * We focus on this part now.
-{{:public:action_5_disassemble_79_.jpg?nolink&800|}}
   * Temporary remove the tape above the ribbon plug on the ribbon pcb.
   * Disconnect the ribbon cable by opening the lash on the ribbon connector and pulling back on the ribbon cable.
-{{:public:action_5_disassemble_80_.jpg?nolink&800|}}
+{{:public:action_6__52_.jpg?nolink&800|}}
-{{:public:action_5_disassemble_81_.jpg?nolink&800|}}
-  * Place the tape back onto the ribbon PCB.
-{{:public:action_5_disassemble_82_.jpg?nolink&800|}}
   * Heat up the ribbon PCB and remove it from the display using some plastic tools.
-{{:public:action_5_disassemble_83_.jpg?nolink&800|}}
+{{:public:action_6__53_.jpg?nolink&800|}}
-  * Lift up the ribbon PCB so its only connected on the left side.
+  * Cut off the display flush at the very left side. Making sure to leave on the black chip on the ribbon PCB side.
-{{:public:action_5_disassemble_84_.jpg?nolink&800|}}
+{{:public:action_6__54_.jpg?nolink&800|}}
-  * Cut off the display flush making sure to leave on the black chip on the ribbon PCB side.
+  * Cut the ribbon PCB like shown in the picture.
-{{:public:action_5_disassemble_85_.jpg?nolink&800|}}
-  * Cut the ribbon PCB like shown in the picture
-{{:public:action_5_assemble__35_.jpg?nolink&800|}}
-  * Fold the ribbon PCB like shown in the picture, make sure to not bend the cable at too much of a angle.
-{{:public:action_5_assemble__36_.jpg?nolink&800|}}
-  * Secure the folded ribbon PCB with some capton tape and carefully cut off the excess tape.
 ===== Assembly Steps =====
-==== Step - Install Thread Inserts ====
-{{:public:action_5_assemble_1_.jpg?nolink&800|}}
-  * Press the thread inserts into the outer side of the naked case using a clean soldering iron set to 220°C.
-  * Use 3x M2*4mm and 1x M2*3mm thread inserts, placing the 3mm insert where the wall thickness is the lowest.
 ==== Step - Install Front Display ====
-{{:public:dji_a4_naked_manual-42.jpg?nolink&800|}}
+{{:public:action_6__39_.jpg?nolink&800|}}
-{{:public:action_5_assemble_2_.jpg?nolink&800|}}
-{{:public:action_5_assemble_3_.jpg?nolink&800|}}
   * Scruff up the surface of the Frontcover a little bit for better adhesion.
@@ Line 296: / Line 275: @@
   * Wait for the epoxy to cure.
-==== Step - Attach Sensor and Button Ribbon Cable ====
-{{:public:action_5_assemble_4_.jpg?nolink&800|}}
-  * Put the Sensors to the cutout on the front side of the case using the double sided tape thats already on the sensor.
-  * If the original double sided tape doesn't stick anymore replace it with some new thin double sided tape.
 ==== Step - Attach ND Filter Adapter ====
-{{:public:action_5_assemble_5_.jpg?nolink&800|}}
+{{:public:action_6__40_.jpg?nolink&800|}}
-  * Screw the aluminum ND filter adapter to the motherboard holder.
+  * Place the motherboard holder into the case, screw on the clear filter from the front.
+  * Secure the motherboard holder with screws.
+==== Step - Attach Lens ====
+{{:public:action_6__42_.jpg?nolink&800|}}
+  * Place the lens assembly into its place.
+  * Secure with the 3x original screws.
+==== Step - Attach Motherboard ====
+{{:public:action_6__43_.jpg?nolink&800|}}
+  * Place the motherboard ontop of the motherboard holder and secure with two screws.
+{{:public:action_6__44_.jpg?nolink&800|}}
+  * Connect the lens ribbon connector and the front display ribbon connector onto the motherboard.
+{{:public:action_6__45_.jpg?nolink&800|}}
+  * Secure the connector with the silver plate and two screws.
+==== Step - Attach Fan ====
+{{:public:action_6__55_.jpg?nolink&800|}}
-==== Step - Assemble Main Components ====
-{{:public:action_5_assemble_6_.jpg?nolink&800|}}
-{{:public:action_5_assemble_7_.jpg?nolink&800|}}
-  * Place the motherboard holder into the naked action 5 front case and secure it with the four silver screws.
-  * Screw an M1.6*6 screw through the top right hole and secure it with an M1.6 nut inside for additional strength.
-{{:public:action_5_assemble_8_.jpg?nolink&800|}}
-  * Attach an ND filter to protect the lens during installation.
-{{:public:action_5_assemble_9_.jpg?nolink&800|}}
-  * Install the mainboard with the two screws.
-{{:public:action_5_assemble_10_.jpg?nolink&800|}}
-  * Install the lens and secure it with three lens screws.
-{{:public:action_5_assemble_11_.jpg?nolink&800|}}
-  * Plug in the lens ribbon cable to the mainboard. Ensure correct alignment before applying force.
-{{:public:action_5_assemble_12_.jpg?nolink&800|}}
-  * Add the silver lens ribbon bracket and secure it with two screws.
-{{:public:action_5_assemble_13_.jpg?nolink&800|}}
-  * Attach the WiFi module holder and secure it with a screw. Use a spare long M1.6 screw from the disassembly.
-{{:public:action_5_assemble_16_.jpg?nolink&800|}}
-  * Add the WiFi module on top of it and secure it with a spare short M1.6 screw from the disassembly.
-{{:public:action_5_assemble_17_.jpg?nolink&800|}}
-  * Add the WiFi module antenna cables and connect them on both sides.
-{{:public:action_5_assemble_18_.jpg?nolink&800|}}
-  * Fold the sensor and button ribbon cable to a package, secure it with tape.
-{{:public:action_5_assemble_19_.jpg?nolink&800|}}
-{{:public:action_5_assemble_20_.jpg?nolink&800|}}
-  * Add the WiFi ribbon cable and connect it on both sides. Ensure correct alignment before applying force.
-  * Make sure the ribbon cable package is placed under the WiFi ribbon cable.
-{{:public:action_5_assemble_22_.jpg?nolink&800|}}
-  * Plug in the front display ribbon cable to the mainboard. Ensure correct alignment before applying force.
-{{:public:action_5_assemble__38_.jpg?nolink&800|}}
-{{:public:action_5_assemble__37_.jpg?nolink&800|}}
-  * Add the back display cable and tape it together to a compact package sitting ontop of the mainboard.
-{{:public:action_5_assemble_25_.jpg?nolink&800|}}
-{{:public:action_5_assemble_26_.jpg?nolink&800|}}
   * Attach the cooling fan to the back case with M2*5 screws using an M2 hex tool.
   * Make sure to get the fan direction right.
-{{:public:action_5_assemble__39_.jpg?nolink&800|}}
-{{:public:action_5_assemble__40_.jpg?nolink&800|}}
-{{:public:action_5_assemble__41_.jpg?nolink&800|}}
-  * Shorten the fan power cables.
-  * Shorten the mainboard power cables.
-  * Shorten the button cable.
-  * Pretinn the 5v, GND and PWR pads.
-  * Solder both red cables to the 5v pad.
-  * Solder both black cables to the GND pad.
-  * Solder the white button cable to the PWR pad.
-{{:public:action_5_assemble__42_.jpg?nolink&800|}}
-  * Plug in the BEC ribbon cable to the mainboard. Ensure correct alignment before applying force.
-{{:public:action_5_assemble__44_.jpg?nolink&800|}}
-  * Connect BEC ribbon cable to the BEC. Ensure correct alignment before applying force.
-  * You will need to open the black bracket, slide in the ribbon cable and then close the bracket again.
-{{:public:action_5_assemble_33_.jpg?nolink&800|}}
-  * Power up the camera using a smoke stopper and the correct voltage to test your camera.
+==== Step - Assemble Main Components ====
+{{:public:action_6__56_.jpg?nolink&800|}}
+{{:public:action_6__57_.jpg?nolink&800|}}
+{{:public:action_6__58_.jpg?nolink&800|}}
 Final assembly