Differences

This shows you the differences between two versions of the page.

--- public:naked-action-5-manual [2025/07/18 09:39] – admin
+++ public:naked-action-5-manual [2025/08/14 14:45] (current) – admin
@@ Line 35: / Line 35: @@
   * Cutter Knife
   * Hobby Knife
+  * Plastic Spudger
   * Pliers
   * Heavy duty side cutters
@@ Line 44: / Line 45: @@
   * Thin double sided tape
   * AWG 28 or 30 silicone wire in the colors red, black and white
+  * 2K Epoxy
 ===== Safety information =====
@@ Line 174: / Line 176: @@
 {{:public:action_5_disassemble_94_.jpg?nolink&800|}}
   * Your camera should now look like this
-{{:public:action_5_disassemble_35_.jpg?nolink&800|}}
-  * Remove all four screws holding the silver pieces of the sensor and button ribbon cable.
-{{:public:action_5_disassemble_36_.jpg?nolink&800|}}
-  * Heat up the cable gently and start to carefully remove it.
-  * Start from the left side, then jump to the right side.
 {{:public:action_5_disassemble_37_.jpg?nolink&800|}}
+  * Remove the remaining two screws holding the silver pieces of the sensor and button ribbon cable of the right side.
   * After the left and right side are free, you need to remove the sensor part of the ribbon cable.
   * Heat this part up gently and remove it carefully with some plastic tools.
@@ Line 270: / Line 268: @@
   * Make sure the orientation of the cable and pad is like shown on the picture.
 {{:public:action_5_disassemble_70_.jpg?nolink&800|}}
-  * Use some UV mask to protect the cable and solderpads and cure with a UV flashlight.
+  * Use some UV mask to protect the cable and solderpads and cure with a UV flashlight or use some other kind of glue.
+{{:public:action_5_disassemble_95_.jpg?nolink&800|}}
+  * The button and sensor ribbon cable should now look like this.
+{{:public:action_5_disassemble_96_.jpg?nolink&800|}}
+  * Cut off the sensor on the left side. Make sure to not damage any lanes going to the connector itself.
@@ Line 314: / Line 316: @@
 {{:public:action_5_disassemble_85_.jpg?nolink&800|}}
   * Cut the ribbon PCB like shown in the picture
+{{:public:action_5_assemble__35_.jpg?nolink&800|}}
+  * Fold the ribbon PCB like shown in the picture, make sure to not bend the cable at too much of a angle.
+{{:public:action_5_assemble__36_.jpg?nolink&800|}}
+  * Secure the folded ribbon PCB with some capton tape and carefully cut off the excess tape.
-TODO Cut Sensor off from Sensor Ribbon Cable
@@ Line 377: / Line 381: @@
 {{:public:action_5_assemble_22_.jpg?nolink&800|}}
   * Plug in the front display ribbon cable to the mainboard. Ensure correct alignment before applying force.
-{{:public:action_5_assemble_23_.jpg?nolink&800|}}
+{{:public:action_5_assemble__38_.jpg?nolink&800|}}
-{{:public:action_5_assemble_24_.jpg?nolink&800|}}
+{{:public:action_5_assemble__37_.jpg?nolink&800|}}
-  * ATTENTION: THE BACK DISPLAY CABLE IS CONNECTED THE WRONG WAY IN ALL FOLLOWING PICUTRES. MAKE SURE TO CONNECT IT THE RIGHT WAY (manual will be updated ASAP)
   * Add the back display cable and tape it together to a compact package sitting ontop of the mainboard.
 {{:public:action_5_assemble_25_.jpg?nolink&800|}}
@@ Line 385: / Line 388: @@
   * Attach the cooling fan to the back case with M2*5 screws using an M2 hex tool.
   * Make sure to get the fan direction right.
-{{:public:action_5_assemble_27_.jpg?nolink&800|}}
+{{:public:action_5_assemble__39_.jpg?nolink&800|}}
-{{:public:action_5_assemble_28_.jpg?nolink&800|}}
+{{:public:action_5_assemble__40_.jpg?nolink&800|}}
-{{:public:action_5_assemble_29_.jpg?nolink&800|}}
+{{:public:action_5_assemble__41_.jpg?nolink&800|}}
-{{:public:action_5_assemble_32_.jpg?nolink&800|}}
   * Shorten the fan power cables.
   * Shorten the mainboard power cables.
@@ Line 396: / Line 398: @@
   * Solder both black cables to the GND pad.
   * Solder the white button cable to the PWR pad.
-{{:public:action_5_assemble_30_.jpg?nolink&800|}}
+{{:public:action_5_assemble__42_.jpg?nolink&800|}}
   * Plug in the BEC ribbon cable to the mainboard. Ensure correct alignment before applying force.
-{{:public:action_5_assemble_31_.jpg?nolink&800|}}
+{{:public:action_5_assemble__44_.jpg?nolink&800|}}
   * Connect BEC ribbon cable to the BEC. Ensure correct alignment before applying force.
   * You will need to open the black bracket, slide in the ribbon cable and then close the bracket again.