public:flowxv3
Differences
This shows you the differences between two versions of the page.
| Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
| public:flowxv3 [2026/01/16 14:03] – laurin | public:flowxv3 [2026/01/20 10:21] (current) – [Step 15 – TPU Stack Cover] laurin | ||
|---|---|---|---|
| Line 11: | Line 11: | ||
| • Place the top plate on a flat surface | • Place the top plate on a flat surface | ||
| + | |||
| • Ensure the countersunk side is facing downward | • Ensure the countersunk side is facing downward | ||
| Line 17: | Line 18: | ||
| • Insert M3x12 mm screws | • Insert M3x12 mm screws | ||
| + | |||
| • Position the arms exactly as shown | • Position the arms exactly as shown | ||
| + | |||
| • Do not fully tighten yet | • Do not fully tighten yet | ||
| Line 24: | Line 27: | ||
| • Add the middle plate | • Add the middle plate | ||
| + | |||
| • Align all holes | • Align all holes | ||
| + | |||
| • Tighten the screws evenly | • Tighten the screws evenly | ||
| Line 31: | Line 36: | ||
| • Install 6 mm TPU spacers | • Install 6 mm TPU spacers | ||
| + | |||
| • Secure them using M3x15 mm screws | • Secure them using M3x15 mm screws | ||
| Line 37: | Line 43: | ||
| TBS Lucid Flight Stack: | TBS Lucid Flight Stack: | ||
| - | • Install the Gorilla Mount as shown | + | Install the Gorilla Mount as shown |
| Other Flight Stacks: | Other Flight Stacks: | ||
| - | • Use M3x28 mm screws | + | Use M3x28 mm screws |
| Tip: Do not overtighten TPU parts. | Tip: Do not overtighten TPU parts. | ||
| Line 48: | Line 54: | ||
| • Install the TPU VTX mount for DJI O4 (Pro) or DJI O3 | • Install the TPU VTX mount for DJI O4 (Pro) or DJI O3 | ||
| + | |||
| • Use M2x5 mm screws | • Use M2x5 mm screws | ||
| + | |||
| • Add aluminum washers on the backside of the plate | • Add aluminum washers on the backside of the plate | ||
| Line 55: | Line 63: | ||
| • Push the TPU pod mount into position | • Push the TPU pod mount into position | ||
| + | |||
| • Insert an M3x20 mm standoff into the designated holes | • Insert an M3x20 mm standoff into the designated holes | ||
| Line 61: | Line 70: | ||
| • Insert M3x20 mm screws | • Insert M3x20 mm screws | ||
| + | |||
| • Add four 3 mm TPU spacers | • Add four 3 mm TPU spacers | ||
| + | |||
| • Leave screws slightly loose for alignment | • Leave screws slightly loose for alignment | ||
| Line 68: | Line 79: | ||
| • Mount the battery plate | • Mount the battery plate | ||
| + | |||
| • Guide screws through: | • Guide screws through: | ||
| + | |||
| – Rear 6 mm TPU spacers | – Rear 6 mm TPU spacers | ||
| + | |||
| – Front TPU pod mount | – Front TPU pod mount | ||
| Line 76: | Line 90: | ||
| • Flip the frame upside down | • Flip the frame upside down | ||
| + | |||
| • Compare your build with the image above | • Compare your build with the image above | ||
| Line 82: | Line 97: | ||
| • Install six M3x20 mm standoffs | • Install six M3x20 mm standoffs | ||
| + | |||
| • Secure the two rear standoffs with M3x6 mm screws | • Secure the two rear standoffs with M3x6 mm screws | ||
| Line 88: | Line 104: | ||
| • Slide the antenna & GPS mount onto the rear standoffs | • Slide the antenna & GPS mount onto the rear standoffs | ||
| + | |||
| • Ensure correct orientation as shown | • Ensure correct orientation as shown | ||
| Line 94: | Line 111: | ||
| • Push the bottom pod mount onto the front standoffs | • Push the bottom pod mount onto the front standoffs | ||
| + | |||
| • Insert an M3x15 mm standoff through the center hole | • Insert an M3x15 mm standoff through the center hole | ||
| Line 100: | Line 118: | ||
| • Install the camera pod plates | • Install the camera pod plates | ||
| + | |||
| • Secure only the top pod mount for now | • Secure only the top pod mount for now | ||
| + | |||
| • Use M3x8 mm screws | • Use M3x8 mm screws | ||
| Line 107: | Line 127: | ||
| • Slide both TPU stack covers into place | • Slide both TPU stack covers into place | ||
| + | |||
| • Install the TPU RX mount | • Install the TPU RX mount | ||
| + | |||
| • Insert an M3x20 mm standoff into the front RX hole | • Insert an M3x20 mm standoff into the front RX hole | ||
| + | |||
| • Use: | • Use: | ||
| + | |||
| – M3x10 mm screws at the pod mount | – M3x10 mm screws at the pod mount | ||
| + | |||
| – M3x8 mm screws at the RX mount | – M3x8 mm screws at the RX mount | ||
| Line 117: | Line 142: | ||
| • Install the bottom plate | • Install the bottom plate | ||
| + | |||
| • Secure with two M3x6 mm screws | • Secure with two M3x6 mm screws | ||
| Line 123: | Line 149: | ||
| • Install front and rear TPU landing gear | • Install front and rear TPU landing gear | ||
| + | |||
| • Use M3x20 mm screws | • Use M3x20 mm screws | ||
| Line 128: | Line 155: | ||
| {{ : | {{ : | ||
| - | ✅ Build complete! | + | Build complete! |
| Your FlowX V3 Frame is now fully assembled and ready for electronics installation. | Your FlowX V3 Frame is now fully assembled and ready for electronics installation. | ||
public/flowxv3.1768572205.txt.gz · Last modified: by laurin