Differences

This shows you the differences between two versions of the page.

--- public:flowxv3 [2026/01/15 14:12] – laurin
+++ public:flowxv3 [2026/01/20 10:21] (current) – [Step 15 – TPU Stack Cover] laurin
@@ Line 1: / Line 1: @@
-====== FlowX V3 Frame Build Guide ======
+====== FlowX V3 Frame Build Manual ======
+===== Introduction =====
+{{ :public:flowx_v3_frame_manual-1.jpg?nolink |}}
+Welcome to the FlowX V3 Frame Build Manual.
+This guide will walk you through the complete frame assembly process step by step.
+===== Step 1 – Top Plate =====
 {{ :public:flowx_v3_frame_manual-49.jpg?nolink&600 |}}
-Start with the Top Plate, the countersinking facing downward.
+• Place the top plate on a flat surface
+• Ensure the countersunk side is facing downward
+===== Step 2 – Install Arms =====
 {{ :public:flowx_v3_frame_manual-47.jpg?nolink&600 |}}
-Add M3Sx12mm Screws and place the Arms like shown above.
+• Insert M3x12 mm screws
+• Position the arms exactly as shown
+• Do not fully tighten yet
+===== Step 3 – Middle Plate =====
 {{ :public:flowx_v3_frame_manual-43.jpg?nolink&600 |}}
-Ad the Middle Plate and tighten the screws.
+• Add the middle plate
+• Align all holes
+• Tighten the screws evenly
+===== Step 4 – TPU Spacers =====
 {{ :public:flowx_v3_frame_manual-42.jpg?nolink&600 |}}
-Install 6mm TPU Spacers with M3Sx15mm screws.
+• Install 6 mm TPU spacers
+• Secure them using M3x15 mm screws
+===== Step 5 – Gorilla Mount =====
 {{ :public:flowx_v3_frame_manual-36.jpg?nolink&600 |}}
-If you use the TBS Lucid Flight Stack, install the Gorilla Mount as shown above.
-If another Stack is used use M3sx28mm Screws.
+TBS Lucid Flight Stack:
+ Install the Gorilla Mount as shown
+Other Flight Stacks:
+ Use M3x28 mm screws
+Tip: Do not overtighten TPU parts.
+===== Step 6 – TPU VTX Mount =====
 {{ :public:flowx_v3_frame_manual-33.jpg?nolink&600 |}}
-Add the TPU VTX Mount for DJI O4 (Pro) or DJI O3 Using M2x5mm Screws and Aluminium washers on the backside of the Plate.
+• Install the TPU VTX mount for DJI O4 (Pro) or DJI O3
+• Use M2x5 mm screws
+• Add aluminum washers on the backside of the plate
+===== Step 7 – TPU Pod Mount =====
 {{ :public:flowx_v3_frame_manual-30.jpg?nolink&600 |}}
-Push the TPU Pod Mount in place and shove a M3x20mm Standoff in the provided holes as shown above.
+• Push the TPU pod mount into position
+• Insert an M3x20 mm standoff into the designated holes
+===== Step 8 – Prepare Battery Plate =====
 {{ :public:flowx_v3_frame_manual-28.jpg?nolink&600 |}}
-Prepare the Battery Plate with M3x20mm Screws and 4 3mm TPU Spacers.
+• Insert M3x20 mm screws
+• Add four 3 mm TPU spacers
+• Leave screws slightly loose for alignment
+===== Step 9 – Install Battery Plate =====
 {{ :public:flowx_v3_frame_manual-24.jpg?nolink&600 |}}
-Install the Battery Plate through the rear 6mm TPU Spacers and the front TPU Pod Mount.
+• Mount the battery plate
+• Guide screws through:
+– Rear 6 mm TPU spacers
+– Front TPU pod mount
+===== Step 10 – Check Your Build =====
 {{ :public:flowx_v3_frame_manual-21.jpg?nolink&600 |}}
-When flipped over, your build should look like this.
+• Flip the frame upside down
+• Compare your build with the image above
+===== Step 11 – Standoffs =====
 {{ :public:flowx_v3_frame_manual-18.jpg?nolink&600 |}}
-Install 6 M3x20mm Standoffs. Use 2 M3x6mm Screws on the rear two standoffs.
+• Install six M3x20 mm standoffs
+• Secure the two rear standoffs with M3x6 mm screws
+===== Step 12 – TPU Antenna & GPS Mount =====
 {{ :public:flowx_v3_frame_manual-13.jpg?nolink&600 |}}
-Push the antenna & GPS Mount onto the rear Standoffs. Be shure to have the orientation right as shown above.
+• Slide the antenna & GPS mount onto the rear standoffs
+• Ensure correct orientation as shown
+===== Step 13 – TPU Bottom Pod Mount =====
 {{ :public:flowx_v3_frame_manual-12.jpg?nolink&600 |}}
-Push the Pod bottom Mount on the two front Standoffs and add a M3x15mm Standoff through the designated hole.
+• Push the bottom pod mount onto the front standoffs
+• Insert an M3x15 mm standoff through the center hole
+===== Step 14 – Camera Pod =====
 {{ :public:flowx_v3_frame_manual-10.jpg?nolink&600 |}}
-Install the Camera Pod Plates. Only screw in at the top Pod Mount yet with M3x8mm Screws.
+• Install the camera pod plates
+• Secure only the top pod mount for now
+• Use M3x8 mm screws
+===== Step 15 – TPU Stack Cover =====
 {{ :public:flowx_v3_frame_manual-7.jpg?nolink&600 |}}
-Add the TPU RX Mount and push in a M3x20mm Standoff in the front hole of the RX Mount. Use M3x10mm Screws at the Pod Mount and M3x8mm Screws in the front for the RX Mount.
-Also push on both side TPU Stack Covers before screwing in the TPU RX Mount.
+• Slide both TPU stack covers into place
+• Install the TPU RX mount
+• Insert an M3x20 mm standoff into the front RX hole
+• Use:
+– M3x10 mm screws at the pod mount
+– M3x8 mm screws at the RX mount
+===== Step 16 – Bottom Plate =====
 {{ :public:flowx_v3_frame_manual-5.jpg?nolink&600 |}}
-Install the bottom Plate using two M3x6mm screws
+• Install the bottom plate
+• Secure with two M3x6 mm screws
+===== Step 17 – TPU Landing Gear =====
 {{ :public:flowx_v3_frame_manual-4.jpg?nolink&600 |}}
-Install the front and back TPU Landing gears using M3x20mm screws.
+• Install front and rear TPU landing gear
+• Use M3x20 mm screws
+===== Finish =====
 {{ :public:flowx_v3_frame_manual-1.jpg?nolink |}}
-That is it, you are finished with building your FlowX V3 Frame!
+Build complete!
+Your FlowX V3 Frame is now fully assembled and ready for electronics installation.