Differences

This shows you the differences between two versions of the page.

--- public:flowxv2 [2026/01/15 14:07] – laurin
+++ public:flowxv2 [2026/01/15 14:13] (current) – created laurin
@@ Line 1: / Line 1: @@
-====== FlowX V3 Frame Build Guide ======
+bruh
-{{ :public:flowx_v3_frame_manual-49.jpg?nolink&600 |}}
-Start with the Top Plate, the countersinking facing downward.
-{{ :public:flowx_v3_frame_manual-47.jpg?nolink&600 |}}
-Add M3Sx12mm Screws and place the Arms like shown above.
-{{ :public:flowx_v3_frame_manual-43.jpg?nolink&600 |}}
-Ad the Middle Plate and tighten the screws.
-{{ :public:flowx_v3_frame_manual-42.jpg?nolink&600 |}}
-Install 6mm TPU Spacers with M3Sx15mm screws.
-{{ :public:flowx_v3_frame_manual-36.jpg?nolink&600 |}}
-If you use the TBS Lucid Flight Stack, install the Gorilla Mount as shown above.
-If another Stack is used use M3sx28mm Screws.
-{{ :public:flowx_v3_frame_manual-33.jpg?nolink&600 |}}
-Add the TPU VTX Mount for DJI O4 (Pro) or DJI O3 Using M2x5mm Screws and Aluminium washers on the backside of the Plate.
-{{ :public:flowx_v3_frame_manual-30.jpg?nolink&600 |}}
-Push the TPU Pod Mount in place and shove a M3x20mm Standoff in the provided holes as shown above.
-{{ :public:flowx_v3_frame_manual-28.jpg?nolink&600 |}}
-Prepare the Battery Plate with M3x20mm Screws and 4 3mm TPU Spacers.
-{{ :public:flowx_v3_frame_manual-24.jpg?nolink&600 |}}
-Install the Battery Plate through the rear 6mm TPU Spacers and the front TPU Pod Mount.
-{{ :public:flowx_v3_frame_manual-21.jpg?nolink&600 |}}
-When flipped over, your build should look like this.
-{{ :public:flowx_v3_frame_manual-18.jpg?nolink&600 |}}
-Install 6 M3x20mm Standoffs. Use 2 M3x6mm Screws on the rear two standoffs.
-{{ :public:flowx_v3_frame_manual-13.jpg?nolink&600 |}}
-Push the antenna & GPS Mount onto the rear Standoffs. Be shure to have the orientation right as shown above.
-{{ :public:flowx_v3_frame_manual-12.jpg?nolink&600 |}}
-Push the Pod bottom Mount on the two front Standoffs and add a M3x15mm Standoff through the designated hole.
-{{ :public:flowx_v3_frame_manual-10.jpg?nolink&600 |}}
-Install the Camera Pod Plates. Only screw in at the top Pod Mount yet with M3x8mm Screws.
-{{ :public:flowx_v3_frame_manual-7.jpg?nolink&600 |}}
-Add the TPU RX Mount and push in a M3x20mm Standoff in the front hole of the RX Mount. Use M3x10mm Screws at the Pod Mount and M3x8mm Screws in the front for the RX Mount.
-Also push on both side TPU Stack Covers before screwing in the TPU RX Mount.
-{{ :public:flowx_v3_frame_manual-5.jpg?nolink&600 |}}
-Install the bottom Plate using two M3x6mm screws
-{{ :public:flowx_v3_frame_manual-4.jpg?nolink&600 |}}
-Install the front and back TPU Landing gears using M3x20mm screws.
-{{ :public:flowx_v3_frame_manual-1.jpg?nolink |}}
-That is it, you are finished with building your FlowX V3 Frame!