Differences

This shows you the differences between two versions of the page.

--- public:flowxminiv2 [2026/02/17 12:46] – laurin
+++ public:flowxminiv2 [2026/03/16 16:08] (current) – admin
@@ Line 1: / Line 1: @@
-====== FlowX Mini V2 Frame Build Manual ======
+{{htmlmetatags>metatag-og:image=(https://wiki.fpvframe.ch/_media/public:icon_fpvframe.png)}}
-===== Introduction =====
+======= Introduction =======
-{{ :public:flowx_mini_ii_frame_manual-1.jpg?nolink |}}
+In this Manual we will walk you through the build process of the FlowX Mini V2.
+There is a frame only manual, and a complete Drone Manual.
+====== FlowX Mini V2 Frame Build Manual ======
 Welcome to the FlowX Mini V2 Frame Build Manual.
@@ Line 107: / Line 110: @@
 • Prepare the bottom plate
 • Install M3x10 mm screws as shown
@@ Line 116: / Line 120: @@
 • Install the middle plate
 • Tighten all screws evenly
@@ Line 122: / Line 127: @@
 • Install the motors using M2x10 mm screws
 • Apply blue Loctite
@@ Line 140: / Line 146: @@
 • Insert M2x12 mm screws through the frame
 • Secure them with rubber donut spacers
 • Install rubber grommets into the FC mounting holes
 • Mount the FC onto the frame
@@ Line 148: / Line 157: @@
 • Cut motor wires to length
 • Leave a small amount of slack
 • Strip and pre-tin the wire ends
@@ Line 160: / Line 171: @@
 • Cut main power wires to approx. 10 cm
 • Pre-tin both ends
@@ Line 174: / Line 186: @@
 • Push the TPU mount into the frame
 • Insert M2 screws through the mount
@@ Line 184: / Line 197: @@
 • Install M2x20 mm standoffs at the rear
 • Secure using M2x8 mm screws
@@ Line 195: / Line 209: @@
 • Strip a small section of insulation from the wires
 • Wrap wires tightly around the capacitor legs
 • Solder securely
-Polarity:
 • Black = Ground / – (short leg)
 • Red = Plus / + (long leg)
@@ Line 212: / Line 228: @@
 • Insert the capacitor into the TPU mount
 • Install the assembly at the front of the frame
@@ Line 217: / Line 234: @@
 • Cut capacitor wires to length
 • Solder them to the FC power pads
@@ Line 224: / Line 242: @@
 • Cut and solder the naked action cam power wire to the FC power pads
-⚠️ Take your time — this step requires clean, precise solder joints.
+Take your time — this step requires clean, precise solder joints.
 ===== Step 14 – XT30 Connector (Optional) =====
@@ Line 236: / Line 254: @@
 • Cut wires to length
 • Solder to the XT30 connector
 • Insulate joints using heat shrink
@@ Line 252: / Line 272: @@
 • Solder RX wires
 • Bend antenna slightly so the bind button remains accessible
 • Cover with shrink tube
@@ Line 259: / Line 281: @@
 • Install the TPU FC cover
 • Mount the receiver on top
 • Use the cover that best fits your FC
@@ Line 265: / Line 289: @@
 • Mount the RX antenna on the rear left arm
 • Secure using two zip ties and the TPU antenna mount
@@ Line 279: / Line 304: @@
 • Trim wires to length (reference image for sizing)
 • Add shrink tube
 • Solder wires according to your hardware configuration
@@ Line 285: / Line 312: @@
 • Twist GPS wires
 • Shield with copper tape
 • Insulate with shrink tube or tape for maximum performance
@@ Line 291: / Line 320: @@
 • Install the GPS module
 • Plug the connector into the FC
@@ Line 301: / Line 331: @@
 • Install the O4/O3 air unit
 • Open the top cover and carefully remove antennas
@@ Line 310: / Line 341: @@
 • Reconnect U.FL antennas
 • Close the air unit
 • Push the TPU antenna mount onto the rear standoffs
+• Connect the VTX with the air unit cable.
 ===== Step 20 – Camera Pod =====
@@ Line 339: / Line 374: @@
 • Mixed batteries: Use the silicone battery pad
 • Same batteries only: Use the TPU battery mount
 TPU battery mount installation:
 • Solder XT30 to PCB plate
 • Insulate with liquid rubber
 • Screw into TPU mount using M2x8 mm screws
@@ Line 358: / Line 396: @@
 {{ :public:flowxmini2_diy_buildmanual-95.jpg?nolink&600 |}}
-🎉 Congratulations! Your build is complete!
+Congratulations! Your build is complete!
 All that’s left is Betaflight configuration, binding your transmitter and goggles, and installing propellers.
-You’re now ready to fly 🚀
+You’re now ready to fly.