FPVFrame.ch

User Tools

Site Tools

Trace: • flowxminiv2 • flowxv3
public:flowxminiv2

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
public:flowxminiv2 [2026/01/20 09:52] – laurinpublic:flowxminiv2 [2026/01/20 09:57] (current) – laurin
Line 2: Line 2:
  
 ===== Introduction ===== ===== Introduction =====
-{{ :public:flowx_mini_ii_frame_manual-1.jpg?nolink&NOCACHE |}}+{{ :public:flowx_mini_ii_frame_manual-1.jpg?nolink |}}
  
 Welcome to the FlowX Mini V2 Frame Build Manual. Welcome to the FlowX Mini V2 Frame Build Manual.
Line 8: Line 8:
  
 ===== Step 1 – Mount Arms on Bottom Plate ===== ===== Step 1 – Mount Arms on Bottom Plate =====
-{{ :public:flowx_mini_ii_frame_manual-33.jpg?nolink&600&NOCACHE |}}+{{ :public:flowx_mini_ii_frame_manual-33.jpg?nolink&600 |}}
  
 • Place the bottom plate on a flat surface • Place the bottom plate on a flat surface
Line 15: Line 15:
  
 ===== Step 2 – Middle Plate ===== ===== Step 2 – Middle Plate =====
-{{ :public:flowx_mini_ii_frame_manual-29.jpg?nolink&600&NOCACHE |}}+{{ :public:flowx_mini_ii_frame_manual-29.jpg?nolink&600 |}}
  
 • Add the middle plate • Add the middle plate
Line 22: Line 22:
  
 ===== Step 3 – TPU Bottom Pod Mount ===== ===== Step 3 – TPU Bottom Pod Mount =====
-{{ :public:flowx_mini_ii_frame_manual-24.jpg?nolink&600&NOCACHE |}}+{{ :public:flowx_mini_ii_frame_manual-24.jpg?nolink&600 |}}
  
 • Press an M2x20 mm standoff into the TPU bottom pod mount • Press an M2x20 mm standoff into the TPU bottom pod mount
Line 29: Line 29:
  
 ===== Step 4 – TPU RX Mount ===== ===== Step 4 – TPU RX Mount =====
-{{ :public:flowx_mini_ii_frame_manual-23.jpg?nolink&600&NOCACHE |}}+{{ :public:flowx_mini_ii_frame_manual-23.jpg?nolink&600 |}}
  
 • Mount the TPU RX mount above the AIO • Mount the TPU RX mount above the AIO
Line 35: Line 35:
  
 ===== Step 5 – TPU VTX Mount ===== ===== Step 5 – TPU VTX Mount =====
-{{ :public:flowx_mini_ii_frame_manual-22.jpg?nolink&600&NOCACHE |}}+{{ :public:flowx_mini_ii_frame_manual-22.jpg?nolink&600 |}}
  
 • Install the TPU VTX mount using M2x5 mm screws • Install the TPU VTX mount using M2x5 mm screws
Line 41: Line 41:
  
 ===== Step 6 – TPU Antenna & GPS Mount ===== ===== Step 6 – TPU Antenna & GPS Mount =====
-{{ :public:flowx_mini_ii_frame_manual-18.jpg?nolink&600&NOCACHE |}}+{{ :public:flowx_mini_ii_frame_manual-18.jpg?nolink&600 |}}
  
 • Install two M2x20 mm standoffs using M2x8 mm screws • Install two M2x20 mm standoffs using M2x8 mm screws
Line 50: Line 50:
  
 ===== Step 7 – Prepare TPU Pod Top & Capacitor Mount ===== ===== Step 7 – Prepare TPU Pod Top & Capacitor Mount =====
-{{ :public:flowx_mini_ii_frame_manual-17.jpg?nolink&600&NOCACHE |}}+{{ :public:flowx_mini_ii_frame_manual-17.jpg?nolink&600 |}}
  
 • Press M2x20 mm standoffs into the designated holes • Press M2x20 mm standoffs into the designated holes
Line 56: Line 56:
  
 ===== Step 8 – Install Pod Mount on Frame ===== ===== Step 8 – Install Pod Mount on Frame =====
-{{ :public:flowx_mini_ii_frame_manual-11.jpg?nolink&600&NOCACHE |}}+{{ :public:flowx_mini_ii_frame_manual-11.jpg?nolink&600 |}}
  
 • Install the TPU pod mount • Install the TPU pod mount
Line 62: Line 62:
  
 ===== Step 9 – Pod Plates ===== ===== Step 9 – Pod Plates =====
-{{ :public:flowx_mini_ii_frame_manual-8.jpg?nolink&600&NOCACHE |}}+{{ :public:flowx_mini_ii_frame_manual-8.jpg?nolink&600 |}}
  
 • Attach both pod plates • Attach both pod plates
Line 68: Line 68:
  
 ===== Step 10 – Top Plate ===== ===== Step 10 – Top Plate =====
-{{ :public:flowx_mini_ii_frame_manual-7.jpg?nolink&600&NOCACHE |}}+{{ :public:flowx_mini_ii_frame_manual-7.jpg?nolink&600 |}}
  
 • Install the top plate • Install the top plate
Line 74: Line 74:
  
 ===== Step 11 – TPU RX Antenna Mount ===== ===== Step 11 – TPU RX Antenna Mount =====
-{{ :public:flowx_mini_ii_frame_manual-2.jpg?nolink&600&NOCACHE |}}+{{ :public:flowx_mini_ii_frame_manual-2.jpg?nolink&600 |}}
  
 • Install the TPU RX antenna mount using zip ties • Install the TPU RX antenna mount using zip ties
Line 84: Line 84:
 ✅ Congratulations! ✅ Congratulations!
 Your FlowX Mini V2 Frame is now fully assembled and ready for electronics installation. Your FlowX Mini V2 Frame is now fully assembled and ready for electronics installation.
 +
 +
public/flowxminiv2.1768902726.txt.gz · Last modified: by laurin
Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki