Differences

This shows you the differences between two versions of the page.

--- public:flowxminiv2 [2026/01/15 15:36] – laurin
+++ public:flowxminiv2 [2026/01/20 09:57] (current) – laurin
@@ Line 1: / Line 1: @@
-====== FlowX Mini V2 Frame build Manual ======
+====== FlowX Mini V2 Frame Build Manual ======
+===== Introduction =====
+{{ :public:flowx_mini_ii_frame_manual-1.jpg?nolink |}}
+Welcome to the FlowX Mini V2 Frame Build Manual.
+This guide will walk you through the complete assembly process step by step.
+===== Step 1 – Mount Arms on Bottom Plate =====
 {{ :public:flowx_mini_ii_frame_manual-33.jpg?nolink&600 |}}
-Start by mounting the Arms on the Bottom Plate using M3x10mm Screws as shown above.
+• Place the bottom plate on a flat surface
+• Mount the arms as shown
+• Secure using M3x10 mm screws
+===== Step 2 – Middle Plate =====
 {{ :public:flowx_mini_ii_frame_manual-29.jpg?nolink&600 |}}
-Fix the Arms in place by screwing on the middle Plate.
+• Add the middle plate
+• Align all arms correctly
+• Tighten the screws to lock the arms in place
+===== Step 3 – TPU Bottom Pod Mount =====
 {{ :public:flowx_mini_ii_frame_manual-24.jpg?nolink&600 |}}
-Push a M2x20mm Standoff into the TPU bottom Pod Mount and install it in the gap between the Bottom and Middleplate using two M2x8mm Screws.
+• Press an M2x20 mm standoff into the TPU bottom pod mount
+• Insert the mount into the gap between the bottom plate and middle plate
+• Secure with two M2x8 mm screws
+===== Step 4 – TPU RX Mount =====
 {{ :public:flowx_mini_ii_frame_manual-23.jpg?nolink&600 |}}
-The TPU RX Mount is mounted above the AIO with M2x12mm Screws.
+• Mount the TPU RX mount above the AIO
+• Secure using M2x12 mm screws
+===== Step 5 – TPU VTX Mount =====
 {{ :public:flowx_mini_ii_frame_manual-22.jpg?nolink&600 |}}
-The TPU VTX Mount is installed with M2x5mm screws. The DJI O4/O3 is placed on top of it.
+• Install the TPU VTX mount using M2x5 mm screws
+• Place the DJI O4 / O3 unit on top of the mount
+===== Step 6 – TPU Antenna & GPS Mount =====
 {{ :public:flowx_mini_ii_frame_manual-18.jpg?nolink&600 |}}
-Install two M2x20mm Standoffs with M2x8mm Screws. Place the TPU Antenna Mount like shown above. If you use a GPS, the TPU GPS Mount goes beneath the Antenna Mount.
+• Install two M2x20 mm standoffs using M2x8 mm screws
+• Place the TPU antenna mount as shown
+Optional:
+• If using a GPS, install the TPU GPS mount beneath the antenna mount
+===== Step 7 – Prepare TPU Pod Top & Capacitor Mount =====
 {{ :public:flowx_mini_ii_frame_manual-17.jpg?nolink&600 |}}
-Prepare the TPU Pod Top and Capacitor Mount by Pressing M2x20mm Standoffsinto the designated holes.
+• Press M2x20 mm standoffs into the designated holes
+• Prepare both the TPU pod top mount and capacitor mount
+===== Step 8 – Install Pod Mount on Frame =====
 {{ :public:flowx_mini_ii_frame_manual-11.jpg?nolink&600 |}}
-Install the TPU Mount on the front of the Middle Plate.
+• Install the TPU pod mount
+• Position it at the front of the middle plate
+===== Step 9 – Pod Plates =====
 {{ :public:flowx_mini_ii_frame_manual-8.jpg?nolink&600 |}}
-Screw on both Pod Plates with M2x8mm Screws.
+• Attach both pod plates
+• Secure using M2x8 mm screws
+===== Step 10 – Top Plate =====
 {{ :public:flowx_mini_ii_frame_manual-7.jpg?nolink&600 |}}
-Screw on the Top Plate with M2x8mm Screws.
+• Install the top plate
+• Secure with M2x8 mm screws
+===== Step 11 – TPU RX Antenna Mount =====
+{{ :public:flowx_mini_ii_frame_manual-2.jpg?nolink&600 |}}
+• Install the TPU RX antenna mount using zip ties
+• Slide the antenna into the mount
+• Secure it with a second zip tie wrapped around the mount and arm
+===== Finish =====
+✅ Congratulations!
+Your FlowX Mini V2 Frame is now fully assembled and ready for electronics installation.