Differences

This shows you the differences between two versions of the page.

--- public:dji-unlock [2024/12/30 15:23] – admin
+++ public:dji-unlock [2024/12/30 15:30] (current) – admin
@@ Line 1: / Line 1: @@
-====== Bind and Fly (BNF) Manual ======
+====== DJI Unlock Manual ======
 =====General Information=====
@@ Line 10: / Line 10: @@
 In order to have a functional unlock you need to unlock both googles and the air unit. Doing the unlock on only one of these devices doesn't help.
+After a update, you have have to repeat these steps.
 =====Googles=====
@@ Line 17: / Line 19: @@
 ====DJI Google V1====
-Create a .txt file, name it naco_pwr
+  - Create a .txt file, name it naco_pwr
-Type pwr_2 inside the text file
+  - Type pwr_2 inside the text file
-Save and close
+  - Save and close
-Copy naco_pwr.txt to a micro SD card (for your DJI FPV goggles)
+  - Copy naco_pwr.txt to a micro SD card
-Power on Goggles and Air Unit, WAIT until you see image from camera
+  - Power on Goggles and Air Unit, WAIT until you see image from camera
-Then put the SD card in DJI goggles
+  - Then put the SD card in DJI goggles
-Restart Goggles
+  - Restart Goggles
 ====DJI Google V2====
-Create a .txt file, name it naco_pwr
+  - Create a .txt file, name it naco_pwr
-Type pwr_2 inside the text file
+  - Type pwr_2 inside the text file
-Save and close
+  - Save and close
-Copy naco_pwr.txt to a micro SD card (for your DJI FPV goggles)
+  - Copy naco_pwr.txt to a micro SD card
-Power on Goggles and Air Unit, WAIT until you see image from camera
+  - Power on Goggles and Air Unit, WAIT until you see image from camera
-Then put the SD card in DJI goggles
+  - Then put the SD card in DJI goggles
-Restart Goggles
+  - Restart Goggles
 ====DJI Google 2====
+  - Create a empty file, name it ham_cfg_support, save and close
+  - Copy ham_cfg_support to a micro SD card
+  - Then SD card in DJI Google 2
+  - Power on DJI Goggle 2
 ====DJI Google 3====
+  - Create a empty file, name it ham_cfg_support, save and close
+  - Copy ham_cfg_support to a micro SD card
+  - Then SD card in DJI Google 3
+  - Power on DJI Goggle 3
 ====DJI Google Integra====
+  * TODO
-**TBS Crossfire**
-  - Turn on your transmitter
-  - Enter Bind mode on your transmitter
-  - Power up the receiver on the drone. Depending on the model USB power might suffice, otherwise you need to connect the Battery. Only do this with propellers removed.
-  - Press the bind button on the Crossfire receiver (check picture below for button location). This needs to be done within 20s after powering the RX.
-  - Confirm bind procedure on your TX.
-{{:public:crossfire_nano_rx.jpg?400|}}
-{{:public:img_9969.jpg?400|}}
-{{:public:img_0114.jpg?400|}}
-{{:public:img_0123.jpg?400|}}
-Depending on the transmitter used, the channel mapping needs to be adapted. This setting can be found in the receiver tab (check picture below). Changing from TAER to AETR or vice versa is usually enough. Make sure the channels on the left side align with your stick axis.
-{{:public:bildschirmfoto_2022-10-11_um_22.30.30.png?400|}}
 =====Air Units=====
@@ Line 64: / Line 62: @@
 ====Air Unit V1====
-Create a .txt file, name it naco_pwr
+  - Create a .txt file, name it naco_pwr
-Type pwr_2 inside the text file
+  - Type pwr_2 inside the text file
-Save and close
+  - Save and close
-Copy naco_pwr.txt to a micro SD card
+  - Copy naco_pwr.txt to a micro SD card
-Then put the SD card in DJI Air Unit V1
+  - Then put the SD card in DJI Air Unit V1
-Power on Air Unit
+  - Power on Air Unit
 ====Vista====
-Create a .txt file, name it naco_pwr
+  - Create a .txt file, name it naco_pwr
-Type pwr_2 inside the text file
+  - Type pwr_2 inside the text file
-Save and close
+  - Save and close
-Power on your Vista
+  - Power on your Vista
-Connect the Vista via USB Cable to a computer
+  - Connect the Vista via USB Cable to a computer
-Wait for the mass storage device to pop up
+  - Wait for the mass storage device to pop up
-Copy naco_pwr.txt to the Vista mass storage
+  - Copy naco_pwr.txt to the Vista mass storage
-Power cycle the Vista
+  - Power cycle the Vista
 ====Air Unit O3====
-Create a empty file, name it ham_cfg_support, save and close
+  - Create a empty file, name it ham_cfg_support, save and close
-Connect the O3 via USB Cable to a computer
+  - Connect the O3 via USB Cable to a computer
-Wait for the mass storage device to pop up
+  - Wait for the mass storage device to pop up
-Copy ham_cfg_support to the O3 mass storage
+  - Copy ham_cfg_support to the O3 mass storage
-Power cycle the O3
+  - Power cycle the O3
 =====Testing the hack=====
-  - Turn on your DJI Goggle
+  - Turn on your google and air unit
-  - Connect the battery to your BNF model. Only do this with props removed or a smokestopper.
+  - Wait for the image from the camera
-  - Wait until the green LED appears on the DJI VTX.
+  - Go into the settings and see if you can change output power / chanels to the FCC ones
-  - Press the red button on your DJI Goggle twice. It should beep twice every second.
-  - Press the button on the DJI VTX. The goggle confirms the binding by beeping twice.