Differences

This shows you the differences between two versions of the page.

--- public:dji-unlock [2024/12/30 15:11] – admin
+++ public:dji-unlock [2024/12/30 15:30] (current) – admin
@@ Line 1: / Line 1: @@
-====== Bind and Fly (BNF) Manual ======
+====== DJI Unlock Manual ======
 =====General Information=====
@@ Line 8: / Line 8: @@
 You have to check with your local law regulations regarding transmission frequencies and transmission power.
+In order to have a functional unlock you need to unlock both googles and the air unit. Doing the unlock on only one of these devices doesn't help.
+After a update, you have have to repeat these steps.
 =====Googles=====
+Look for the correct version of your google and do the required steps listed below
 ====DJI Google V1====
+  - Create a .txt file, name it naco_pwr
+  - Type pwr_2 inside the text file
+  - Save and close
+  - Copy naco_pwr.txt to a micro SD card
+  - Power on Goggles and Air Unit, WAIT until you see image from camera
+  - Then put the SD card in DJI goggles
+  - Restart Goggles
 ====DJI Google V2====
+  - Create a .txt file, name it naco_pwr
+  - Type pwr_2 inside the text file
+  - Save and close
+  - Copy naco_pwr.txt to a micro SD card
+  - Power on Goggles and Air Unit, WAIT until you see image from camera
+  - Then put the SD card in DJI goggles
+  - Restart Goggles
 ====DJI Google 2====
+  - Create a empty file, name it ham_cfg_support, save and close
+  - Copy ham_cfg_support to a micro SD card
+  - Then SD card in DJI Google 2
+  - Power on DJI Goggle 2
 ====DJI Google 3====
+  - Create a empty file, name it ham_cfg_support, save and close
+  - Copy ham_cfg_support to a micro SD card
+  - Then SD card in DJI Google 3
+  - Power on DJI Goggle 3
 ====DJI Google Integra====
+  * TODO
-**TBS Crossfire**
-  - Turn on your transmitter
-  - Enter Bind mode on your transmitter
-  - Power up the receiver on the drone. Depending on the model USB power might suffice, otherwise you need to connect the Battery. Only do this with propellers removed.
-  - Press the bind button on the Crossfire receiver (check picture below for button location). This needs to be done within 20s after powering the RX.
-  - Confirm bind procedure on your TX.
-{{:public:crossfire_nano_rx.jpg?400|}}
-{{:public:img_9969.jpg?400|}}
-{{:public:img_0114.jpg?400|}}
-{{:public:img_0123.jpg?400|}}
-Depending on the transmitter used, the channel mapping needs to be adapted. This setting can be found in the receiver tab (check picture below). Changing from TAER to AETR or vice versa is usually enough. Make sure the channels on the left side align with your stick axis.
-{{:public:bildschirmfoto_2022-10-11_um_22.30.30.png?400|}}
 =====Air Units=====
-  - Turn on your DJI Goggle
+Look for the correct version of your video transmitter and do the required steps listed below
-  - Connect the battery to your BNF model. Only do this with props removed or a smokestopper.
-  - Wait until the green LED appears on the DJI VTX.
-  - Press the red button on your DJI Goggle twice. It should beep twice every second.
-  - Press the button on the DJI VTX. The goggle confirms the binding by beeping twice.
-{{:public:dji-goggle-_3_.jpg?300|}}
-{{:public:dji-fpv-air-unit.jpg?300|}}
-{{:public:caddx-unite-vista-hd-vtx.jpg?300|}}
-=====Change Flight Modes=====
-The Stock configuration of our BNFs is made for TBS Tango 2 with the following switch assignments.
-{{:public:tango2_manual_modes.jpg?400|}}
-If you want to change the function of the buttons on your remote controller you need to assign AUX channels to each flight mode. This can be done within Betaflight.
-  - Connect the drone via USB port of the flight controller to your computer
-  - launch Betaflight configurator
-  - Connect to the correspondent port
-  - Navigate to "Modes" tab
-  - Choose AUTO for the mode in question and press the corresponding button on your TX
-  - Dont forget to hit save!
-{{:public:bildschirmfoto_2022-11-05_um_11.07.22.png?400|}}
+====Air Unit V1====
-==IMPORTANT==
+  - Create a .txt file, name it naco_pwr
+  - Type pwr_2 inside the text file
+  - Save and close
+  - Copy naco_pwr.txt to a micro SD card
+  - Then put the SD card in DJI Air Unit V1
+  - Power on Air Unit
-For all models that support GPS rescue: The GPS rescue should not be activated if you are within 100m of the starting point. If the drone is within 100m radius of the starting point and GPS rescue is activated, the drone will drop form the sky. Only activate GPS Rescue manually if the drone is more than 100m away from its starting point.
+====Vista====
-=====Change Rates=====
+  - Create a .txt file, name it naco_pwr
+  - Type pwr_2 inside the text file
+  - Save and close
+  - Power on your Vista
+  - Connect the Vista via USB Cable to a computer
+  - Wait for the mass storage device to pop up
+  - Copy naco_pwr.txt to the Vista mass storage
+  - Power cycle the Vista
-Rates affect the flight feel and determine the maximum speed of rotation around each axis for your drone. Our presets allow smooth and cinematic flight, but it is a good idea to experiment with the rates on order to find your personal settings.
+====Air Unit O3====
-  - Connect the drone via USB port of the flight controller to your computer
+  - Create a empty file, name it ham_cfg_support, save and close
-  - launch Betaflight configurator
+  - Connect the O3 via USB Cable to a computer
-  - Connect to the correspondent port
+  - Wait for the mass storage device to pop up
-  - Navigate to "PID" tab
+  - Copy ham_cfg_support to the O3 mass storage
-  - Swap to "Rateprofile settings" tab
+  - Power cycle the O3
-  - Adapt the parameters to your needs
-  - Dont forget to hit save!
-{{:public:bildschirmfoto_2022-10-11_um_22.25.45.png?400|}}
+=====Testing the hack=====
+  - Turn on your google and air unit
+  - Wait for the image from the camera
+  - Go into the settings and see if you can change output power / chanels to the FCC ones