Differences

This shows you the differences between two versions of the page.

--- public:cx360-diy-pro-manual [2024/04/06 10:28] – admin
+++ public:cx360-diy-pro-manual [2024/12/09 18:01] (current) – ↷ Page moved from internal:public:cx360-diy-pro-manual to public:cx360-diy-pro-manual admin
@@ Line 135: / Line 135: @@
 ==== Step - Servo ====
 {{:public:cx360_diy_22.jpg?800|}}
 Cut the last AUX power cable pair to length and solder the BEC to it. Push the servo into its designed mount on the camera mount and shorten the servo cable. Solder the signal wire of the servo onto the LED strip pad on the fc. Now solder the 5v+ and GND wire of the servo to the coresponding outputs of the bec. Conformal coat the BEC and put it into some heatshrink. Now all solder connections on the FC are done and you can also coat the topside of the FC with conformal coating. Place the BEC for the servo into the camera mount holder.
 ==== Step - Add landing gear mount ====
-{{:public:cx360_diy_23.jpg?800|}}
+{{:public:cx360_diy_23_new.jpg?800|}}
 Mount the landing gear PETG mounts with four M2 6mm screws. They should be mounted upside down not like in the picture. TODO
@@ Line 146: / Line 147: @@
 Remove the two M1.6 screws holding the antennas and remove the antennas. Then flip the O3 upside down and remove the four screws. Now align the TPU air unit holder and screw it in place using the originial four M1.6 screws.
-{{:public:cx360_diy_26.jpg?800|}}
 Now remove the four M2 nuts you may used to secure the FC and exchange it with the air unit. The four M2 12mm screws will screw directly into the O3 air unit TPU part. Make sure to not tighten it too much.
@@ Line 153: / Line 152: @@
 ==== Step - Standoffs ====
-{{:public:cx360_diy_27.jpg?800|}}
+{{:public:cx360_diy_27_new.jpg?800|}}
 Now add all the missing standoffs to the frame. Front and back uses M2 22mm standoffs while the bumpers use M2 20mm standoffs. Secure them using M2 6mm countersunk screws.
 ==== Step - Air Unit camera and antenna ====
-{{:public:cx360_diy_28.jpg?800|}}
+{{:public:cx360_diy_28_new.jpg?800|}}
 Now you can add the two O3 camera holder TPU parts. Simply slide them over the two M2 22mm standoffs in the front. Also slide down the antenna mounts on the standoffs facing in the direction shown in the picture.
-{{:public:cx360_diy_29.jpg?800|}}
+{{:public:cx360_diy_29_new.jpg?800|}}
 Now secure the O3 camera to the O3 camera holder TPU parts by using two M2 4mm screws. Also add the provided TrueRC antennas into the TPU mount (heating up the TPU part can help getting it to fit) and connect the antennas to the UFL ports on the O3. Now secure the UFL ports with the plate and the two original M1.6 screws.
+==== Step - SD extension mount & Immortal T ====
+{{:public:cx360_diy_30_new.jpg?800|}}
+Secure the Immortal T antenna with some tape (in the picture the antenna is mounted with cable ties but they tend to appear in the camera view).
+Clip the TPU SD extension mount to the standoffs in the back.
 ==== Step - Topplate ====
-{{:public:cx360_diy_30.jpg?800|}}
+{{:public:cx360_diy_31_new.jpg?800|}}
 Now you add the topplate and screw it down using M2 6mm countersunk screws.
 ==== Step - USB-C extension and battery plates ====
-{{:public:cx360_diy_31.jpg?800|}}
+{{:public:cx360_diy_32_new.jpg?800|}}
 Now screw down the USB-C extension onto the topplate into the designed slot using two M2 6mm screws. You can now also add the two battery plates ontop of the battery mount. Also use some M2 washers in between.
-==== Step - Top camera protection ====
+==== Step - Landing Gear ====
-{{:public:cx360_diy_32.jpg?800|}}
+{{:public:cx360_diy_33_new.jpg?800|}}
-Add the top camera protection PETG part to the frame and screw it down.
+Prepare the landing gear like in the picture above.
+Use the M2 screws to secure the carbon fibre plates to te aluminium standoff and then secure the piston arm to the plate with a M1.6 screw. Use two countered M1.6 nuts to secure them into place. We also recomend to use loctite here.
+{{:public:cx360_diy_34_new.jpg?800|}}
+Add the servo horn to the servo and secure it with the included screw.
+{{:public:cx360_diy_35_new.jpg?800|}}
+Mount the piston plate to the servo horn onto the lowest hole with the included screw.
 ==== Step - Bottom camera protection ====
-{{:public:cx360_diy_33.jpg?800|}}
+{{:public:cx360_diy_36_new.jpg?800|}}
 Add the bottom camera protection PETG part to the frame and screw it down.
-==== Step - Landing gear ====
+==== Step - Top camera protection ====
+{{:public:cx360_diy_37_new.jpg?800|}}
-Prepare the landing gear by screwing the long standoff onto the both supporting arms. Add the piston arms to the supporting arm. Screw this contraption into the landing gear mount using two M3 6mm screws. Now secure the piston arms to the servo using the screw provided with the servo.
+Add the top camera protection PETG part to the frame and screw it down.
+==== Step - Propellers ====
+{{:public:cx360_diy_38_new.jpg?800|}}
+Add the propellers to the motors by using two M2 x 8mm screws.
+Make sure the direction is correct. We are using a pusher setup here.
 ==== Step - Finish ====
+Flash Betaflight 4.5 to the flightcontroller and add our diff that you can find below.
+Then check the motor direction and change it if needed.
+Now bind your RX to your TX and change the chanel mapping.
+Now unlock your DJI O3 and bind it with your google.
+Always make sure to use a smoke stopper or remove the propellers for working on the bench