Differences

This shows you the differences between two versions of the page.

--- public:cx360-bnf-manual [2024/10/05 17:59] – laurin
+++ public:cx360-bnf-manual [2024/12/09 18:01] (current) – ↷ Page moved from internal:public:cx360-bnf-manual to public:cx360-bnf-manual admin
@@ Line 5: / Line 5: @@
 ===== General Information =====
-The CinematiX360 demands caution to prevent injury. Never connect the battery without removing propellers or using a smokestopper while on the bench.
+The Cityflitzer demands caution to prevent injury. Never connect the battery without removing propellers or using a smokestopper while on the bench.
 It's advisable to inspect and retighten all screws after the initial successful flights due to motor-induced vibrations. Regularly checking these screws ensures continual drone reliability.
@@ Line 12: / Line 12: @@
-==== Insta360 ONE RS 1" edition information ====
+==== DJI O3 naked Information ====
-The Insta360 ONE RS has to be placed carefully inside the frame. To make sure the cameras view is unobstructed, it is recommended to check the view by taking a short test video in flight before shooting.
+The DJI O3 in the Cityflitzer is stripped down to its 'naked' form to minimize weight and maximize performance. However, this setup can lead to increased heat buildup when stationary. To prevent overheating, avoid prolonged idle time before takeoff. Once airborne, the airflow will effectively cool the air unit.
-We provide a Micro SD Card extender to simplify sd card access. Push the metal cover forward and flip open to add the micro SD card inside, the close it and pull the metal cover backwards to lock the SD card. We usually add tape around the SD card to avoid unintentional ejection.
+For smooth, high-quality footage, we strongly recommend following the 90° shutter rule when configuring the O3 camera. In bright, sunny conditions, ND filters are essential to maintain optimal performance. Each BNF Cityflitzer comes with a set of ND filters included.
 ==== Lipo information ====
-The CinematiX 360 BNF is meant to be powered by two 4s 650mAh lipos. Bonka 4s 650 and Tattu r-line 4s 650 fit inside the 3d printed battery slots. Push in the batteries on both sides and slide the balance connector into the provided slot. Make sure the batteries do not obstruct the gear mechanics before plugging powering the drone.
+The CityflitzerBNF is meant to be powered by either 4s 650mAh or 4s 850mAh LiPos. Bonka Tattu 4s 650 fit inside the 3d printed battery slots. The 3D Print can be changed easily by loosing the following 4 screws (two on the bottom, 2 on the XT30 power connector.
-{{:public:CF_manual-5.jpg}}
+{{:public:360_feature_10.jpg}}
-{{:public:CF_manual-6.jpg}}
 ==== Landing gear mechanics information ====
@@ Line 30: / Line 29: @@
 ===== Before the first flight =====
+==== Mounting the 360 camera into the frame ====
+  * Remove 4 m2 button head screws on the 3D printed camera cover on the bottom side of the Drone.
+  * Remove the cover from the Drone
+  * Push in the 360 camera for proper sitting in the counterpart
+  * Put the 3D printed cover back in its place and tighten the 4 screws.
+  * Connect the USB C connector in the back to power the camera.
+{{:public:360_feature_12.jpg}}
 ==== Binding your Remote Controller ====
@@ Line 42: / Line 52: @@
 {{:public:crossfire_nano_rx.jpg?400|}}
-{{:public:CF_manual-3.jpg?400|}}
+{{:public:360_feature_4.jpg?400|}}
 Adjust channel mapping in the receiver tab based on your transmitter. Typically, changing from TAER to AETR (or vice versa) aligns channels with stick axis.
@@ Line 71: / Line 81: @@
 {{:public:dji-goggles-2.jpg?400|}}
-{{:public:CF_manual-4.jpeg?400|}}
+{{:public:dji_o3_bind.button.jpeg?400|}}
+==== Landing gear Setup ====
+The landing gear can be retracted with a switch on your remote controller. The Servo is connected to the flight controller and mapped to RX AUX Channel 3. You can change the channel to your preferred switch in the Servo tab in Betaflight configurator.
 ===== Change Rates =====