User Tools

Site Tools


public:cityflitzer-bnf-manual

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
public:cityflitzer-bnf-manual [2024/10/05 18:10] laurinpublic:cityflitzer-bnf-manual [2024/12/09 18:01] (current) – ↷ Page moved from internal:public:cityflitzer-bnf-manual to public:cityflitzer-bnf-manual admin
Line 17: Line 17:
  
 For smooth, high-quality footage, we strongly recommend following the 90° shutter rule when configuring the O3 camera. In bright, sunny conditions, ND filters are essential to maintain optimal performance. Each BNF Cityflitzer comes with a set of ND filters included. For smooth, high-quality footage, we strongly recommend following the 90° shutter rule when configuring the O3 camera. In bright, sunny conditions, ND filters are essential to maintain optimal performance. Each BNF Cityflitzer comes with a set of ND filters included.
 +
 +{{:public:CF_manual-7.jpg?400|}}
 +{{:public:CF_manual-8.jpg?400|}}
  
 ==== Lipo information ==== ==== Lipo information ====
Line 22: Line 25:
 The Cityflitzer BNF is designed to be powered by either 4S 650mAh or 4S 850mAh LiPos, with Bonka and Tattu batteries fitting perfectly into the 3D-printed battery slot. The slot is also easy to swap out—simply loosen the two screws on the bottom and two more on the XT30 power connector for a quick change. The Cityflitzer BNF is designed to be powered by either 4S 650mAh or 4S 850mAh LiPos, with Bonka and Tattu batteries fitting perfectly into the 3D-printed battery slot. The slot is also easy to swap out—simply loosen the two screws on the bottom and two more on the XT30 power connector for a quick change.
  
-{{:public:CF_manual-5.jpg}} +{{:public:CF_manual-5.jpg?400|}} 
-{{:public:CF_manual-6.jpg}}+{{:public:CF_manual-6.jpg?400|}}
  
  
Line 32: Line 35:
 To remove the Hood, remove the 4 lowest screws that hold the pod together (2 on each side). The hood will then pop away. Make sure to put the standoffs in the slots before reassembly to make sure all screws can be tightened properly.  To remove the Hood, remove the 4 lowest screws that hold the pod together (2 on each side). The hood will then pop away. Make sure to put the standoffs in the slots before reassembly to make sure all screws can be tightened properly. 
  
-{{:public:CF_manual-1.jpeg?400|}} +{{:public:CF_manual-1.jpg?400|}} 
-{{:public:CF_manual-10.jpeg?400|}}+{{:public:CF_manual-10.jpg?400|}}
  
 ==== Binding your Remote Controller ==== ==== Binding your Remote Controller ====
Line 42: Line 45:
   * Enter Bind mode on your transmitter.   * Enter Bind mode on your transmitter.
   * Power up the drone's receiver. USB power might suffice, or connect the battery (without propellers).   * Power up the drone's receiver. USB power might suffice, or connect the battery (without propellers).
-  * Press the bind button on the Crossfire receiver within 20s of powering the RX.+  * Press the bind button on the Crossfire receiver within 20s of powering the RX (alternatively the bind mode can be activated in betaflight RX tab)
   * Confirm the bind procedure on your TX.   * Confirm the bind procedure on your TX.
  
Line 75: Line 78:
  
 {{:public:dji-goggles-2.jpg?400|}} {{:public:dji-goggles-2.jpg?400|}}
-{{:public:CF_manual-4.jpeg?400|}}+{{:public:CF_manual-4.jpg?400|}}
  
  
public/cityflitzer-bnf-manual.1728151815.txt.gz · Last modified: 2024/11/20 17:51 (external edit)

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki