Differences

This shows you the differences between two versions of the page.

--- public:cityflitzer-bnf-manual [2024/10/05 18:03] – laurin
+++ public:cityflitzer-bnf-manual [2024/12/09 18:01] (current) – ↷ Page moved from internal:public:cityflitzer-bnf-manual to public:cityflitzer-bnf-manual admin
@@ Line 1: / Line 1: @@
-====== CinematiX360 BNF Manual ======
+====== Cityflitzer BNF Manual ======
 {{:public:cityflitzer_sls_1.jpg?600|}}
@@ Line 5: / Line 5: @@
 ===== General Information =====
-The CinematiX360 demands caution to prevent injury. Never connect the battery without removing propellers or using a smokestopper while on the bench.
+The Cityflitzer demands caution to prevent injury. Never connect the battery without removing propellers or using a smokestopper while on the bench.
 It's advisable to inspect and retighten all screws after the initial successful flights due to motor-induced vibrations. Regularly checking these screws ensures continual drone reliability.
@@ Line 12: / Line 12: @@
-==== Insta360 ONE RS 1" edition information ====
+==== DJI O3 Naked information ====
-The Insta360 ONE RS has to be placed carefully inside the frame. To make sure the cameras view is unobstructed, it is recommended to check the view by taking a short test video in flight before shooting.
+The DJI O3 in the Cityflitzer is stripped down to its 'naked' form to minimize weight and maximize performance. However, this setup can lead to increased heat buildup when stationary. To prevent overheating, avoid prolonged idle time before takeoff. Once airborne, the airflow will effectively cool the air unit.
-We provide a Micro SD Card extender to simplify sd card access. Push the metal cover forward and flip open to add the micro SD card inside, the close it and pull the metal cover backwards to lock the SD card. We usually add tape around the SD card to avoid unintentional ejection.
+For smooth, high-quality footage, we strongly recommend following the 90° shutter rule when configuring the O3 camera. In bright, sunny conditions, ND filters are essential to maintain optimal performance. Each BNF Cityflitzer comes with a set of ND filters included.
+{{:public:CF_manual-7.jpg?400|}}
+{{:public:CF_manual-8.jpg?400|}}
 ==== Lipo information ====
-The CinematiX 360 BNF is meant to be powered by two 4s 650mAh lipos. Bonka 4s 650 and Tattu r-line 4s 650 fit inside the 3d printed battery slots. Push in the batteries on both sides and slide the balance connector into the provided slot. Make sure the batteries do not obstruct the gear mechanics before plugging powering the drone.
+The Cityflitzer BNF is designed to be powered by either 4S 650mAh or 4S 850mAh LiPos, with Bonka and Tattu batteries fitting perfectly into the 3D-printed battery slot. The slot is also easy to swap out—simply loosen the two screws on the bottom and two more on the XT30 power connector for a quick change.
-{{:public:CF_manual-5.jpg}}
+{{:public:CF_manual-5.jpg?400|}}
-{{:public:CF_manual-6.jpg}}
+{{:public:CF_manual-6.jpg?400|}}
-==== Landing gear mechanics information ====
-The Landing gear is designed to protect the lens for scratches while being retractable to allow free camera view. The mechanism is mechanically supported to allow bumpy landings, it is however not designed as a crash protection. It is also recommended to avoid continuous operation of the servo mechanism to limit servo heating when not in flight.
 ===== Before the first flight =====
+==== Removing the Hood ====
+To remove the Hood, remove the 4 lowest screws that hold the pod together (2 on each side). The hood will then pop away. Make sure to put the standoffs in the slots before reassembly to make sure all screws can be tightened properly.
+{{:public:CF_manual-1.jpg?400|}}
+{{:public:CF_manual-10.jpg?400|}}
 ==== Binding your Remote Controller ====
-The CinematiX 360 receiver is located on the outside of the main camera holder. For binding follow this procedure:
+The Cityflitzer receiver is located under the hood. You can enter bind mode through the "Bind" button in betaflight receiver tab or you can open the hood to manually access the bind button.
   * Power on your transmitter.
   * Enter Bind mode on your transmitter.
   * Power up the drone's receiver. USB power might suffice, or connect the battery (without propellers).
-  * Press the bind button on the Crossfire receiver within 20s of powering the RX.
+  * Press the bind button on the Crossfire receiver within 20s of powering the RX (alternatively the bind mode can be activated in betaflight RX tab)
   * Confirm the bind procedure on your TX.
@@ Line 71: / Line 78: @@
 {{:public:dji-goggles-2.jpg?400|}}
-{{:public:CF_manual-4.jpeg?400|}}
+{{:public:CF_manual-4.jpg?400|}}