Differences

This shows you the differences between two versions of the page.

--- public:bnfmanual [2022/10/11 21:07] – laurin
+++ public:bnfmanual [2024/12/09 18:01] (current) – ↷ Page moved from internal:public:bnfmanual to public:bnfmanual admin
@@ Line 5: / Line 5: @@
 Our BNFs are no toys. Please be aware of injury especially with the bigger models. Do not plug in the battery when on the bench unless propellers are removed or a smokestopper is used.
-After the first successful flights, it is recommended to check all screws on the drone and retighten if necessary. Due to vibrations on the drone, this service should be repeated after each few flights to ensure permanent functioning of the FPV drone.
+After the first successful flights, it is recommended to check all screws on the drone and retighten if necessary. Due to vibrations from the motors it is recommended to check the screws after each few flights to ensure permanent reliability of the drone.
-If you have bought one of our BNFs together with the InstantFly Kit, all the procedures mentioned below have been taken care of already. It is however a good idea to read through the process for a general understanding of procedures and optional changes to tailor the drone to your personal preferences! Our settings will provide a good start for beginners and experienced pilots for cinematic flying.
+If you have bought one of our BNFs together with the InstantFly Kit, all the procedures mentioned below have been taken care of already. It is however a good idea to read through the process for a general understanding of procedures and optional changes to tailor the drone to your personal preferences! Our settings will provide a good start for beginners as well as experienced pilots for cinematic flying.
 =====Binding your Remote Controller=====
@@ Line 36: / Line 36: @@
   - Press the button on the DJI VTX. The goggle confirms the binding by beeping twice.
-{{:public:dji-goggle-_3_.jpg?330|}}
+{{:public:dji-goggle-_3_.jpg?300|}}
-{{:public:dji-fpv-air-unit.jpg?330|}}
+{{:public:dji-fpv-air-unit.jpg?300|}}
-{{:public:caddx-unite-vista-hd-vtx.jpg?330|}}
+{{:public:caddx-unite-vista-hd-vtx.jpg?300|}}
 =====Change Flight Modes=====
+The Stock configuration of our BNFs is made for TBS Tango 2 with the following switch assignments.
+{{:public:tango2_manual_modes.jpg?400|}}
 If you want to change the function of the buttons on your remote controller you need to assign AUX channels to each flight mode. This can be done within Betaflight.
@@ Line 46: / Line 50: @@
   - Connect the drone via USB port of the flight controller to your computer
   - launch Betaflight configurator
-  - Connect to the correspondant port
+  - Connect to the correspondent port
   - Navigate to "Modes" tab
   - Choose AUTO for the mode in question and press the corresponding button on your TX
   - Dont forget to hit save!
-{{:public:bildschirmfoto_2022-10-11_um_22.27.18.png?400|}}
+{{:public:bildschirmfoto_2022-11-05_um_11.07.22.png?400|}}
+==IMPORTANT==
+For all models that support GPS rescue: The GPS rescue should not be activated if you are within 100m of the starting point. If the drone is within 100m radius of the starting point and GPS rescue is activated, the drone will drop form the sky. Only activate GPS Rescue manually if the drone is more than 100m away from its starting point.
 =====Change Rates=====
@@ Line 59: / Line 67: @@
   - Connect the drone via USB port of the flight controller to your computer
   - launch Betaflight configurator
-  - Connect to the correspondant port
+  - Connect to the correspondent port
   - Navigate to "PID" tab
   - Swap to "Rateprofile settings" tab