{{htmlmetatags>metatag-og:image=(https://wiki.fpvframe.ch/_media/public:icon_fpvframe.png)}}

====== FlowX V3 Frame Build Manual ======

===== Introduction =====
{{ :public:flowx_v3_frame_manual-1.jpg?nolink |}}

Welcome to the FlowX V3 Frame Build Manual.
This guide will walk you through the complete frame assembly process step by step.

===== Step 1 – Top Plate =====
{{ :public:flowx_v3_frame_manual-49.jpg?nolink&600 |}}

• Place the top plate on a flat surface

• Ensure the countersunk side is facing downward

===== Step 2 – Install Arms =====
{{ :public:flowx_v3_frame_manual-47.jpg?nolink&600 |}}

• Insert M3x12 mm screws

• Position the arms exactly as shown

• Do not fully tighten yet

===== Step 3 – Middle Plate =====
{{ :public:flowx_v3_frame_manual-43.jpg?nolink&600 |}}

• Add the middle plate

• Align all holes

• Tighten the screws evenly

===== Step 4 – TPU Spacers =====
{{ :public:flowx_v3_frame_manual-42.jpg?nolink&600 |}}

• Install 6 mm TPU spacers

• Secure them using M3x15 mm screws

===== Step 5 – Gorilla Mount =====
{{ :public:flowx_v3_frame_manual-36.jpg?nolink&600 |}}

TBS Lucid Flight Stack:
 Install the Gorilla Mount as shown

Other Flight Stacks:
 Use M3x28 mm screws

Tip: Do not overtighten TPU parts.

===== Step 6 – TPU VTX Mount =====
{{ :public:flowx_v3_frame_manual-33.jpg?nolink&600 |}}

• Install the TPU VTX mount for DJI O4 (Pro) or DJI O3

• Use M2x5 mm screws

• Add aluminum washers on the backside of the plate

===== Step 7 – TPU Pod Mount =====
{{ :public:flowx_v3_frame_manual-30.jpg?nolink&600 |}}

• Push the TPU pod mount into position

• Insert an M3x20 mm standoff into the designated holes

===== Step 8 – Prepare Battery Plate =====
{{ :public:flowx_v3_frame_manual-28.jpg?nolink&600 |}}

• Insert M3x20 mm screws

• Add four 3 mm TPU spacers

• Leave screws slightly loose for alignment

===== Step 9 – Install Battery Plate =====
{{ :public:flowx_v3_frame_manual-24.jpg?nolink&600 |}}

• Mount the battery plate

• Guide screws through:

– Rear 6 mm TPU spacers

– Front TPU pod mount

===== Step 10 – Check Your Build =====
{{ :public:flowx_v3_frame_manual-21.jpg?nolink&600 |}}

• Flip the frame upside down

• Compare your build with the image above

===== Step 11 – Standoffs =====
{{ :public:flowx_v3_frame_manual-18.jpg?nolink&600 |}}

• Install six M3x20 mm standoffs

• Secure the two rear standoffs with M3x6 mm screws

===== Step 12 – TPU Antenna & GPS Mount =====
{{ :public:flowx_v3_frame_manual-13.jpg?nolink&600 |}}

• Slide the antenna & GPS mount onto the rear standoffs

• Ensure correct orientation as shown

===== Step 13 – TPU Bottom Pod Mount =====
{{ :public:flowx_v3_frame_manual-12.jpg?nolink&600 |}}

• Push the bottom pod mount onto the front standoffs

• Insert an M3x15 mm standoff through the center hole

===== Step 14 – Camera Pod =====
{{ :public:flowx_v3_frame_manual-10.jpg?nolink&600 |}}

• Install the camera pod plates

• Secure only the top pod mount for now

• Use M3x8 mm screws

===== Step 15 – TPU Stack Cover =====
{{ :public:flowx_v3_frame_manual-7.jpg?nolink&600 |}}

• Slide both TPU stack covers into place

• Install the TPU RX mount

• Insert an M3x20 mm standoff into the front RX hole

• Use:

– M3x10 mm screws at the pod mount

– M3x8 mm screws at the RX mount

===== Step 16 – Bottom Plate =====
{{ :public:flowx_v3_frame_manual-5.jpg?nolink&600 |}}

• Install the bottom plate

• Secure with two M3x6 mm screws

===== Step 17 – TPU Landing Gear =====
{{ :public:flowx_v3_frame_manual-4.jpg?nolink&600 |}}

• Install front and rear TPU landing gear

• Use M3x20 mm screws

===== Finish =====
{{ :public:flowx_v3_frame_manual-1.jpg?nolink |}}

Build complete!
Your FlowX V3 Frame is now fully assembled and ready for electronics installation.